Return to rc.vpn CVS log

Up to [local] / src / share / ipsec

general cleanup, including:
removal of extra flows for gateway to network; make manual keying
optional, allows 'acquire' with isakmpd; no need for sed;
add ipsecadm flush; ok ho@

#!/bin/sh
#	$OpenBSD: rc.vpn,v 1.16 2002/12/04 15:03:56 markus Exp $
#
# Richard Reiner, Ph.D., FSC Internet Corp.
# rreiner@fscinternet.com
# v0.81 / 26Jul98
#
# Modifications and cleanup by H. Olsson <ho@openbsd.org>, 28Aug99
#
# rc.vpn -- configure IPsec in tunnel mode for a mesh of N local and
#           M remote networks. (N x M mesh)
#
# For this to work, you will need to have these enabled (in /etc/sysctl.conf):
#   'sysctl -w net.inet.ip.forwarding=1'   (IP packet routing)
#   'sysctl -w net.inet.esp.enable=1'      (IPsec ESP protocol)

# XXX The configuration parameters should be moved to another file.

# Uncomment to debug (and not execute) commands
#DEBUG=echo

# Gateway adresses
GW_LOCAL=192.168.254.254
GW_REMOTE=192.168.1.2

# Local and remote networks, numbered
LOCAL_NET_0="192.168.254.0/24"
LOCAL_NET_1="192.168.253.0/24"
REMOTE_NET_0="192.168.1.0/24"
REMOTE_NET_1="192.168.2.0/24"

# Optional, use for manual keying only
# Crypto options and keys, note that key/iv lengths need to correspond
# to the selected encryption and authentication algorithms.
ENC=3des
AUTH=sha1
SPI_OUT=1000
SPI_IN=1001
KEYFILE=/etc/esp-enc-key
AUTHKEYFILE=/etc/esp-auth-key

#############################################################################
############# -- NO CHANGES SHOULD BE NEEDED BELOW THIS LINE -- #############
#############################################################################

ipsecadm=/sbin/ipsecadm

#
# Sanity, be verbose about errors.
# XXX In a 1 x M mesh, ip.forwarding may not be strictly necessary.
#

abort=0
if [ `/usr/sbin/sysctl -n net.inet.esp.enable` == 0 ]; then
	echo "$0: variable 'net.inet.esp.enable' (IPsec ESP protocol)"
	abort=1
fi
if [ `/usr/sbin/sysctl -n net.inet.ip.forwarding` == 0 ]; then
	echo "$0: variable 'net.inet.ip.forwarding' (IP forwarding/routing)"
	abort=1
fi
if [ ${abort} = 1 ]; then
	echo "$0: must be enabled in /etc/sysctl.conf. Aborting VPN setup." 
	[ ! -n "${DEBUG}" ] && exit 0
fi

$DEBUG $ipsecadm flush

#
# Setup the manual SAs
#

if [ "$ENC" ]; then
	$DEBUG $ipsecadm new esp -src $GW_LOCAL -dst $GW_REMOTE \
		-forcetunnel -spi $SPI_OUT -enc $ENC -auth $AUTH \
		-keyfile $KEYFILE -authkeyfile $AUTHKEYFILE

	$DEBUG $ipsecadm new esp -src $GW_REMOTE -dst $GW_LOCAL \
		-forcetunnel -spi $SPI_IN -enc $ENC -auth $AUTH \
		-keyfile $KEYFILE -authkeyfile $AUTHKEYFILE
fi

#
# Setup the Flows, aka SPD
#

FLOW="$DEBUG $ipsecadm flow -proto esp -src $GW_LOCAL -dst $GW_REMOTE"
FLOWIN="$FLOW -in -require -addr"
FLOWOUT="$FLOW -out -require -addr"

# local gateway to remote gateway

$FLOWOUT ${GW_LOCAL}/32  ${GW_REMOTE}/32
$FLOWIN  ${GW_REMOTE}/32 ${GW_LOCAL}/32

# each local net to each remote net

localcount=0
while true; do
	local_net=`eval "echo \\\$LOCAL_NET_${localcount}"`
	if [ "x${local_net}" == "x" ]; then
		break;
	fi
	remotecount=0
	while true; do
		remote_net=`eval "echo \\\$REMOTE_NET_${remotecount}"`
		if [ "x${remote_net}" == "x" ]; then
			break;
		fi
		$FLOWOUT $local_net  $remote_net
		$FLOWIN  $remote_net $local_net
		remotecount=$(($remotecount + 1))
	done
	localcount=$(($localcount + 1))
done

exit 0