version 1.29, 2004/03/05 10:53:58 |
version 1.29.2.1, 2004/08/19 04:13:27 |
|
|
Specifies the ciphers allowed for protocol version 2 |
Specifies the ciphers allowed for protocol version 2 |
in order of preference. |
in order of preference. |
Multiple ciphers must be comma-separated. |
Multiple ciphers must be comma-separated. |
|
The supported ciphers are |
|
.Dq 3des-cbc , |
|
.Dq aes128-cbc , |
|
.Dq aes192-cbc , |
|
.Dq aes256-cbc , |
|
.Dq aes128-ctr , |
|
.Dq aes192-ctr , |
|
.Dq aes256-ctr , |
|
.Dq arcfour , |
|
.Dq blowfish-cbc , |
|
and |
|
.Dq cast128-cbc . |
The default is |
The default is |
.Bd -literal |
.Bd -literal |
``aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,arcfour, |
``aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,arcfour, |
|
|
server, instead of using the default system TCP timeout. |
server, instead of using the default system TCP timeout. |
This value is used only when the target is down or really unreachable, |
This value is used only when the target is down or really unreachable, |
not when it refuses the connection. |
not when it refuses the connection. |
|
.It Cm ControlMaster |
|
Enables the sharing of multiple sessions over a single network connection. |
|
When set to |
|
.Dq yes |
|
.Nm ssh |
|
will listen for connections on a control socket specified using the |
|
.Cm ControlPath |
|
argument. |
|
Additional sessions can connect to this socket using the same |
|
.Cm ControlPath |
|
with |
|
.Cm ControlMaster |
|
set to |
|
.Dq no |
|
(the default). |
|
These sessions will reuse the master instance's network connection rather |
|
than initiating new ones. |
|
Setting this to |
|
.Dq ask |
|
will cause |
|
.Nm ssh |
|
to listen for control connections, but require confirmation using the |
|
.Ev SSH_ASKPASS |
|
program before they are accepted (see |
|
.Xr ssh-add 1 |
|
for details). |
|
.It Cm ControlPath |
|
Specify the path to the control socket used for connection sharing. |
|
See |
|
.Cm ControlMaster |
|
above. |
.It Cm DynamicForward |
.It Cm DynamicForward |
Specifies that a TCP/IP port on the local machine be forwarded |
Specifies that a TCP/IP port on the local machine be forwarded |
over the secure channel, and the application |
over the secure channel, and the application |
|
|
.Cm ForwardX11Trusted |
.Cm ForwardX11Trusted |
option is also enabled. |
option is also enabled. |
.It Cm ForwardX11Trusted |
.It Cm ForwardX11Trusted |
If the this option is set to |
If this option is set to |
.Dq yes |
.Dq yes |
then remote X11 clients will have full access to the original X11 display. |
then remote X11 clients will have full access to the original X11 display. |
If this option is set to |
If this option is set to |
|
|
Specifies that |
Specifies that |
.Nm ssh |
.Nm ssh |
should only use the authentication identity files configured in the |
should only use the authentication identity files configured in the |
.Nm |
.Nm |
files, |
files, |
even if the |
even if the |
.Nm ssh-agent |
.Nm ssh-agent |
|
|
The default is |
The default is |
.Dq yes . |
.Dq yes . |
Note that this option applies to protocol version 1 only. |
Note that this option applies to protocol version 1 only. |
|
.It Cm SendEnv |
|
Specifies what variables from the local |
|
.Xr environ 7 |
|
should be sent to the server. |
|
Note that environment passing is only supported for protocol 2, the |
|
server must also support it, and the server must be configured to |
|
accept these environment variables. |
|
Refer to |
|
.Cm AcceptEnv |
|
in |
|
.Xr sshd_config 5 |
|
for how to configure the server. |
|
Variables are specified by name, which may contain the wildcard characters |
|
.Ql \&* |
|
and |
|
.Ql \&? . |
|
Multiple environment variables may be separated by whitespace or spread |
|
across multiple |
|
.Cm SendEnv |
|
directives. |
|
The default is not to send any environment variables. |
.It Cm ServerAliveInterval |
.It Cm ServerAliveInterval |
Sets a timeout interval in seconds after which if no data has been received |
Sets a timeout interval in seconds after which if no data has been received |
from the server, |
from the server, |
|
|
This file is used by the |
This file is used by the |
.Nm ssh |
.Nm ssh |
client. |
client. |
This file does not usually contain any sensitive information, |
Because of the potential for abuse, this file must have strict permissions: |
but the recommended permissions are read/write for the user, and not |
read/write for the user, and not accessible by others. |
accessible by others. |
|
.It Pa /etc/ssh/ssh_config |
.It Pa /etc/ssh/ssh_config |
Systemwide configuration file. |
Systemwide configuration file. |
This file provides defaults for those |
This file provides defaults for those |