===================================================================
RCS file: /cvsrepo/anoncvs/cvs/src/usr.bin/ssh/sshd_config.5,v
retrieving revision 1.35.2.1
retrieving revision 1.35.2.2
diff -u -r1.35.2.1 -r1.35.2.2
--- src/usr.bin/ssh/sshd_config.5	2005/03/10 16:28:28	1.35.2.1
+++ src/usr.bin/ssh/sshd_config.5	2005/09/02 03:45:01	1.35.2.2
@@ -34,7 +34,7 @@
 .\" (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
 .\" THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
 .\"
-.\" $OpenBSD: sshd_config.5,v 1.35.2.1 2005/03/10 16:28:28 brad Exp $
+.\" $OpenBSD: sshd_config.5,v 1.35.2.2 2005/09/02 03:45:01 brad Exp $
 .Dd September 25, 1999
 .Dt SSHD_CONFIG 5
 .Os
@@ -168,24 +168,18 @@
 .Dq aes128-ctr ,
 .Dq aes192-ctr ,
 .Dq aes256-ctr ,
+.Dq arcfour128 ,
+.Dq arcfour256 ,
 .Dq arcfour ,
 .Dq blowfish-cbc ,
 and
 .Dq cast128-cbc .
 The default is
 .Bd -literal
-  ``aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,arcfour,
-    aes192-cbc,aes256-cbc,aes128-ctr,aes192-ctr,aes256-ctr''
+  ``aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,arcfour128,
+    arcfour256,arcfour,aes192-cbc,aes256-cbc,aes128-ctr,
+    aes192-ctr,aes256-ctr''
 .Ed
-.It Cm ClientAliveInterval
-Sets a timeout interval in seconds after which if no data has been received
-from the client,
-.Nm sshd
-will send a message through the encrypted
-channel to request a response from the client.
-The default
-is 0, indicating that these messages will not be sent to the client.
-This option applies to protocol version 2 only.
 .It Cm ClientAliveCountMax
 Sets the number of client alive messages (see above) which may be
 sent without
@@ -213,14 +207,25 @@
 .Cm ClientAliveCountMax
 is left at the default, unresponsive ssh clients
 will be disconnected after approximately 45 seconds.
+.It Cm ClientAliveInterval
+Sets a timeout interval in seconds after which if no data has been received
+from the client,
+.Nm sshd
+will send a message through the encrypted
+channel to request a response from the client.
+The default
+is 0, indicating that these messages will not be sent to the client.
+This option applies to protocol version 2 only.
 .It Cm Compression
-Specifies whether compression is allowed.
+Specifies whether compression is allowed, or delayed until
+the user has authenticated successfully.
 The argument must be
-.Dq yes
+.Dq yes ,
+.Dq delayed ,
 or
 .Dq no .
 The default is
-.Dq yes .
+.Dq delayed .
 .It Cm DenyGroups
 This keyword can be followed by a list of group name patterns, separated
 by spaces.
@@ -327,7 +332,7 @@
 Specifies whether
 .Nm sshd
 should ignore the user's
-.Pa $HOME/.ssh/known_hosts
+.Pa ~/.ssh/known_hosts
 during
 .Cm RhostsRSAAuthentication
 or
@@ -630,7 +635,7 @@
 .It Cm UseDNS
 Specifies whether
 .Nm sshd
-should lookup the remote host name and check that
+should look up the remote host name and check that
 the resolved host name for the remote IP address maps back to the
 very same IP address.
 The default is