pub/OpenBSD/2.1/ directory on
one of the mirror sites
! All applicable copyrights and credits are in the src.tar.gz, --- 27,40 ----
pub/OpenBSD/2.1/ directory on
one of the mirror sites
! All applicable copyrights and credits are in the src.tar.gz, *************** *** 87,93 **** Quick installer information for people familiar with OpenBSD, and the use of the new "disklabel -E" command. If you are at all confused when installing OpenBSD, read the relevant INSTALL.* file as listed above! !
Play with your BIOS options, and see if you can enable booting off a --- 87,93 ---- Quick installer information for people familiar with OpenBSD, and the use of the new "disklabel -E" command. If you are at all confused when installing OpenBSD, read the relevant INSTALL.* file as listed above! !
Play with your BIOS options, and see if you can enable booting off a *************** *** 100,113 **** Unix, use "dd if=<file> of=/dev/<device> bs=32k" (where device could be "floppy" or "rfd0c" or "rfd0a"). Use properly formatted perfect floppies with NO BAD BLOCKS or you will lose. !
Using CD1, tell the BOOT ROM to load the file CD1:\2.1\arc\bsd.rd. If that does not work, create a MS-DOS filesystem using your vendor's arc setup program, copy CD1:2.1/arc/bsd.rd to there and attempt to boot it. !
To boot off CD1, type "boot cdrom 2.1/sparc/bsd.rd", or --- 100,113 ---- Unix, use "dd if=<file> of=/dev/<device> bs=32k" (where device could be "floppy" or "rfd0c" or "rfd0a"). Use properly formatted perfect floppies with NO BAD BLOCKS or you will lose. !
Using CD1, tell the BOOT ROM to load the file CD1:\2.1\arc\bsd.rd. If that does not work, create a MS-DOS filesystem using your vendor's arc setup program, copy CD1:2.1/arc/bsd.rd to there and attempt to boot it. !
To boot off CD1, type "boot cdrom 2.1/sparc/bsd.rd", or *************** *** 120,144 **** floppy, insert "inst.fs". Answer a bunch of questions. Reboot from the "kc.fs" floppy. This time, when the floppy is ejected simply re-insert "kc.fs" again and answer a different set of questions. !
Write the simpleroot21.fs onto the start of the disk using dd on another machine. After moving the disk drive, use "boot -f rz(0,0,0)/bsd" (2100/3100) or "boot 5/rz0a/bsd" (5000). Alternatively, install via network as described in detail in INSTALL.pmax. !
Create BSD partitions according to INSTALL.amiga's preparation section. Mount the CD2 under AmigaOS as device CD0: Next, execute the following CLI command: "CD0:2.1/amiga/utils/loadbsd CD0:2.1/amiga/bsd.rd". !
You can boot over the network by following the instructions in INSTALL.hp300. !
Your alpha must use SRM firmware (not ARC). If you have a CDROM, you --- 120,144 ---- floppy, insert "inst.fs". Answer a bunch of questions. Reboot from the "kc.fs" floppy. This time, when the floppy is ejected simply re-insert "kc.fs" again and answer a different set of questions. !
Write the simpleroot21.fs onto the start of the disk using dd on another machine. After moving the disk drive, use "boot -f rz(0,0,0)/bsd" (2100/3100) or "boot 5/rz0a/bsd" (5000). Alternatively, install via network as described in detail in INSTALL.pmax. !
Create BSD partitions according to INSTALL.amiga's preparation section. Mount the CD2 under AmigaOS as device CD0: Next, execute the following CLI command: "CD0:2.1/amiga/utils/loadbsd CD0:2.1/amiga/bsd.rd". !
You can boot over the network by following the instructions in INSTALL.hp300. !
Your alpha must use SRM firmware (not ARC). If you have a CDROM, you *************** *** 146,152 **** CDROM drive identifier). Otherwise, write CD2:2.1/alpha/floppy.fs to a floppy and boot that by typing "boot dva0". If this fails, you can place bsd.rd on some other device and boot it, or use the provided simpleroot. !
Boot MacOS as normal and partition your disk with the appropriate A/UX --- 146,152 ---- CDROM drive identifier). Otherwise, write CD2:2.1/alpha/floppy.fs to a floppy and boot that by typing "boot dva0". If this fails, you can place bsd.rd on some other device and boot it, or use the provided simpleroot. !
Boot MacOS as normal and partition your disk with the appropriate A/UX *************** *** 156,162 **** BSD/Mac68k Installer to copy all the sets in CD1:2.1/mac68k/ onto your partitions. Finally, you will be ready to configure the BSD/Mac68k Booter with the location of your kernel and boot the system. !
Theo has no real idea. In the rush to get everything else done, the --- 156,162 ---- BSD/Mac68k Installer to copy all the sets in CD1:2.1/mac68k/ onto your partitions. Finally, you will be ready to configure the BSD/Mac68k Booter with the location of your kernel and boot the system. !
Theo has no real idea. In the rush to get everything else done, the *************** *** 173,179 **** src.tar.gz contains a source archive starting at /usr/src. This file contains everything you need except for the kernel sources, which are in a separate archive. To extract: -
# mkdir -p /usr/src # cd /usr/src --- 173,178 ---- *************** *** 183,189 **** srcsys.tar.gz contains a source archive starting at /usr/src/sys. This file contains all the kernel sources you need to rebuild kernels. To extract: -
# mkdir -p /usr/src/sys # cd /usr/src --- 182,187 ---- *************** *** 204,210 ****Ports Tree
A ports tree archive is also provided. To extract: -
# cd /usr # tar xvfz /tmp/ports.tar.gz --- 202,207 ---- *************** *** 214,220 ****The ports/ subdirectory is a checkout of the OpenBSD ports tree. Go ! read http://www.OpenBSD.org/faq/faq15.html if you know nothing about ports at this point. This text is not a manual of how to use ports. Rather, it is a set of notes meant to kickstart the user on the --- 211,217 ----
The ports/ subdirectory is a checkout of the OpenBSD ports tree. Go ! read https://www.OpenBSD.org/faq/faq15.html if you know nothing about ports at this point. This text is not a manual of how to use ports. Rather, it is a set of notes meant to kickstart the user on the *************** *** 234,240 **** order to keep current with the, you must make the ports/ tree available on a read-write medium and update the tree with a command like: -
--- 231,236 ----# cd [portsdir]/; cvs -d anoncvs@server.openbsd.org:/cvs update -Pd