-
+
+
Copyright 1997, Theo de Raadt.
@@ -28,7 +40,7 @@
pub/OpenBSD/2.1/ directory on
one of the mirror sites
+
|
-
-
+ |
Released sometime around June 1, 1997. Copyright 1997, Theo de Raadt. @@ -28,7 +40,7 @@ pub/OpenBSD/2.1/ directory on
one of the mirror sites
+ |
-
Following this are the instructions if you had purchased a CDROM set instead of attempting to do an alternate form of install. The instructions for doing an ftp (or other style of) install are very similar; the CDROM instructions are left intact so that you can see how much easier it would have been if you had purchased a CDROM instead. -
Please refer to the following files on the two CDROMs for extensive details on how to install OpenBSD 2.1 on your machine: -
-
+
Quick installer information for people familiar with OpenBSD, and the use of the new "disklabel -E" command. If you are at all confused when installing OpenBSD, read the relevant INSTALL.* file as listed above!
-
Play with your BIOS options, and see if you can enable booting off a CD; try using CD1. If not, write CD1:2.1/i386/floppy21.fs to a @@ -86,14 +101,14 @@ be "floppy" or "rfd0c" or "rfd0a"). Use properly formatted perfect floppies with NO BAD BLOCKS or you will lose.
-
Using CD1, tell the BOOT ROM to load the file CD1:\2.1\arc\bsd.rd. If that does not work, create a MS-DOS filesystem using your vendor's arc setup program, copy CD1:2.1/arc/bsd.rd to there and attempt to boot it.
-
To boot off CD1, type "boot cdrom 2.1/sparc/bsd.rd", or "b sd(0,6,0)2.1/sparc/bsd.rd" depending on your ROM version. @@ -106,25 +121,25 @@ the "kc.fs" floppy. This time, when the floppy is ejected simply re-insert "kc.fs" again and answer a different set of questions.
-
Write the simpleroot21.fs onto the start of the disk using dd on another machine. After moving the disk drive, use "boot -f rz(0,0,0)/bsd" (2100/3100) or "boot 5/rz0a/bsd" (5000). Alternatively, install via network as described in detail in INSTALL.pmax.
-
Create BSD partitions according to INSTALL.amiga's preparation section. Mount the CD2 under AmigaOS as device CD0: Next, execute the following CLI command: "CD0:2.1/amiga/utils/loadbsd CD0:2.1/amiga/bsd.rd".
-
You can boot over the network by following the instructions in INSTALL.hp300.
-
Your alpha must use SRM firmware (not ARC). If you have a CDROM, you can try "boot -fi 2.1/alpha/bsd.rd dkaX" (use "show device" to find your @@ -132,7 +147,7 @@ floppy and boot that by typing "boot dva0". If this fails, you can place bsd.rd on some other device and boot it, or use the provided simpleroot.
-
Boot MacOS as normal and partition your disk with the appropriate A/UX configurations. Then, extract the Macside utilities from @@ -142,16 +157,21 @@ partitions. Finally, you will be ready to configure the BSD/Mac68k Booter with the location of your kernel and boot the system.
-
Theo has no real idea. In the rush to get everything else done, the install stuff for the mvme68k was never completed. Enough pieces are included so that a really skilled person could find a way to install it; perhaps using netbooting. Good luck! +
-
src.tar.gz contains a source archive starting at /usr/src. This file contains everything you need except for the kernel sources, which are in a separate archive. To extract: @@ -178,11 +198,13 @@ Using these files results in a much faster initial CVS update than you could expect from a fresh checkout of the full OpenBSD source tree. -
+
-
A ports tree archive is also provided. To extract:
@@ -231,6 +253,4 @@ interested in seeing a port added, would like to help out, or just would like to know more, the mailing list ports@openbsd.org is a good place to know. - - - +