pub/OpenBSD/2.1/ directory on
@@ -55,7 +46,6 @@
Following this are the instructions if you had purchased a CDROM set instead of attempting to do @@ -68,18 +58,28 @@ Please refer to the following files on the two CDROMs for extensive details on how to install OpenBSD 2.1 on your machine:
+
-
Play with your BIOS options, and see if you can enable booting off a CD; try using CD1. If not, write CD1:2.1/i386/floppy21.fs to a @@ -101,14 +101,14 @@ be "floppy" or "rfd0c" or "rfd0a"). Use properly formatted perfect floppies with NO BAD BLOCKS or you will lose.
-
Using CD1, tell the BOOT ROM to load the file CD1:\2.1\arc\bsd.rd. If that does not work, create a MS-DOS filesystem using your vendor's arc setup program, copy CD1:2.1/arc/bsd.rd to there and attempt to boot it.
-
To boot off CD1, type "boot cdrom 2.1/sparc/bsd.rd", or "b sd(0,6,0)2.1/sparc/bsd.rd" depending on your ROM version. @@ -121,25 +121,25 @@ the "kc.fs" floppy. This time, when the floppy is ejected simply re-insert "kc.fs" again and answer a different set of questions.
-
Write the simpleroot21.fs onto the start of the disk using dd on another machine. After moving the disk drive, use "boot -f rz(0,0,0)/bsd" (2100/3100) or "boot 5/rz0a/bsd" (5000). Alternatively, install via network as described in detail in INSTALL.pmax.
-
Create BSD partitions according to INSTALL.amiga's preparation section. Mount the CD2 under AmigaOS as device CD0: Next, execute the following CLI command: "CD0:2.1/amiga/utils/loadbsd CD0:2.1/amiga/bsd.rd".
-
You can boot over the network by following the instructions in INSTALL.hp300.
-
Your alpha must use SRM firmware (not ARC). If you have a CDROM, you can try "boot -fi 2.1/alpha/bsd.rd dkaX" (use "show device" to find your @@ -147,7 +147,7 @@ floppy and boot that by typing "boot dva0". If this fails, you can place bsd.rd on some other device and boot it, or use the provided simpleroot.
-
Boot MacOS as normal and partition your disk with the appropriate A/UX configurations. Then, extract the Macside utilities from @@ -157,44 +157,42 @@ partitions. Finally, you will be ready to configure the BSD/Mac68k Booter with the location of your kernel and boot the system.
-
Theo has no real idea. In the rush to get everything else done, the install stuff for the mvme68k was never completed. Enough pieces are included so that a really skilled person could find a way to install it; perhaps using netbooting. Good luck!
src.tar.gz contains a source archive starting at /usr/src. This file contains everything you need except for the kernel sources, which are in a separate archive. To extract:
-
-# mkdir -p /usr/src -# cd /usr/src -# tar xvfz /tmp/src.tar.gz -+
+# mkdir -p /usr/src +# cd /usr/src +# tar xvfz /tmp/src.tar.gz +
srcsys.tar.gz contains a source archive starting at /usr/src/sys. This file contains all the kernel sources you need to rebuild kernels. To extract:
-
-# mkdir -p /usr/src/sys -# cd /usr/src -# tar xvfz /tmp/srcsys.tar.gz -+
+# mkdir -p /usr/src/sys +# cd /usr/src +# tar xvfz /tmp/srcsys.tar.gz +
Both of these trees are a regular CVS checkout. Using these trees it is possible to get a head-start on using the anoncvs servers as -described at http://www.OpenBSD.org/anoncvs.html. +described here. Using these files results in a much faster initial CVS update than you could expect from a fresh checkout of the full OpenBSD source tree. @@ -203,17 +201,17 @@
A ports tree archive is also provided. To extract:
-
-# cd /usr -# tar xvfz /tmp/ports.tar.gz -# cd ports -# ls ++# cd /usr +# tar xvfz /tmp/ports.tar.gz +# cd ports +# ls ... -+
The ports/ subdirectory is a checkout of the OpenBSD ports tree. Go read http://www.OpenBSD.org/faq/faq15.html @@ -237,9 +235,9 @@ available on a read-write medium and update the tree with a command like:
-
-# cd [portsdir]/; cvs -d anoncvs@server.openbsd.org:/cvs update -Pd -+
+# cd [portsdir]/; cvs -d anoncvs@server.openbsd.org:/cvs update -Pd +
[Of course, you must replace the local directory and server name here with the location of your ports collection and a nearby anoncvs @@ -251,6 +249,6 @@
Finally, despite ports' youth, help is never far. If you're interested in seeing a port added, would like to help out, or just -would like to know more, the mailing list ports@openbsd.org is a good -place to know. +would like to know more, the mailing list +ports@openbsd.org is a good place to know.