=================================================================== RCS file: /cvsrepo/anoncvs/cvs/www/22.html,v retrieving revision 1.37 retrieving revision 1.38 diff -u -r1.37 -r1.38 --- www/22.html 2016/08/15 02:22:05 1.37 +++ www/22.html 2019/05/27 22:55:18 1.38 @@ -1,35 +1,47 @@ - - - + + + + OpenBSD 2.2 - - - + + +

-OpenBSD -2.2 +OpenBSD +2.2

+ + +
- -

+CD 2.2 +

 Released sometime around December 1, 1997.
Copyright 1997, Theo de Raadt.
-ISBN 0-9683637-0-9. +ISBN 0-9683637-0-9.

  • Order a CDROM from our ordering system.
  • See the information on The FTP page for a list of mirror machines -
  • Go to the pub/OpenBSD/2.2/ directory on +
  • Go to the pub/OpenBSD/2.2/ directory on one of the mirror sites
  • Have a look at The 2.2 Errata page for a list of bugs and workarounds. @@ -38,13 +50,14 @@ All applicable copyrights and credits are in the src.tar.gz, sys.tar.gz, xenocara.tar.gz, ports.tar.gz files, or in the files fetched via ports.tar.gz. -
    +
- + +
+

How to install

+

-

How to install

-

Following this are the instructions if you had purchased a CDROM set instead of attempting to do an alternate form of install. The instructions for doing an ftp (or @@ -56,25 +69,30 @@ Please refer to the following files on the two CDROM's for extensive details on how to install OpenBSD 2.2 on your machine:

-

+ +
+ +
+
+ +

Quick installer information for people familiar with OpenBSD, and the use of the new "disklabel -E" command. If you are at all confused when installing OpenBSD, read the relevant INSTALL.* file as listed above!

-

i386:

+

i386:

Play with your BIOS options, and see if you can enable booting off a CD; try using CD1. If not, write CD1:2.2/i386/floppy22.fs to a @@ -87,14 +105,14 @@ be "floppy" or "rfd0c" or "rfd0a"). Use properly formatted perfect floppies with NO BAD BLOCKS or you will lose.

-

ARC:

+

ARC:

Using CD1, tell the BOOT ROM to load the file CD1:\2.2\arc\bsd.rd. If that does not work, create a MS-DOS filesystem using your vendor's arc setup program, copy CD1:2.2/arc/bsd.rd to there and attempt to boot it.

-

SPARC:

+

SPARC:

To boot off CD1, type "boot cdrom 2.2/sparc/bsd.rd", or "b sd(0,6,0)2.2/sparc/bsd.rd" depending on your ROM version. @@ -107,25 +125,25 @@ the "kc.fs" floppy. This time, when the floppy is ejected simply re-insert "kc.fs" again and answer a different set of questions.

-

PMAX:

+

PMAX:

Write the simpleroot22.fs onto the start of the disk using dd on another machine. After moving the disk drive, use "boot -f rz(0,0,0)/bsd" (2100/3100) or "boot 5/rz0a/bsd" (5000). Alternatively, install via network as described in detail in INSTALL.pmax.

-

AMIGA:

+

AMIGA:

Create BSD partitions according to INSTALL.amiga's preparation section. Mount the CD2 under AmigaOS as device CD0: Next, execute the following CLI command: "CD0:2.2/amiga/utils/loadbsd CD0:2.2/amiga/bsd.rd".

-

HP300:

+

HP300:

You can boot over the network by following the instructions in INSTALL.hp300.

-

ALPHA:

+

ALPHA:

Your alpha must use SRM firmware (not ARC). If you have a CDROM, you can try "boot -fi 2.2/alpha/bsd.rd dkaX" (use "show device" to find your @@ -133,7 +151,7 @@ floppy and boot that by typing "boot dva0". If this fails, you can place bsd.rd on some other device and boot it, or use the provided simpleroot.

-

MAC68K:

+

MAC68K:

Boot MacOS as normal and partition your disk with the appropriate A/UX configurations. Then, extract the Macside utilities from @@ -143,16 +161,19 @@ partitions. Finally, you will be ready to configure the BSD/Mac68k Booter with the location of your kernel and boot the system.

-

MVME68K:

+

MVME68K:

Theo has no real idea. In the rush to get everything else done, the install stuff for the mvme68k was never completed. Enough pieces are included so that a really skilled person could find a way to install it; perhaps using netbooting. Good luck! +

+
+ +
+

NOTES ABOUT THE SOURCE CODE:

-

NOTES ABOUT THE SOURCE CODE:

-

src.tar.gz contains a source archive starting at /usr/src. This file contains everything you need except for the kernel sources, which are in a separate archive. To extract: @@ -179,11 +200,13 @@ Using these files results in a much faster initial CVS update than you could expect from a fresh checkout of the full OpenBSD source tree. -

+

+
+ +
+

PORTS TREE

-

PORTS TREE

-

A ports tree archive is also provided. To extract: 

@@ -232,6 +255,4 @@
 interested in seeing a port added, would like to help out, or just
 would like to know more, the mailing list ports@openbsd.org is a good
 place to know.
-
-
-
+