![[OpenBSD]](images/logo25.gif){kind=logo}
! OpenBSD
! 2.5
! OpenBSD
! 2.5
! 
!
Released May 19, 1999.
Copyright 1997-1999, Theo de Raadt.
! ISBN - 0-9683637-3-3.
! OpenBSD
! 2.5
|
!
! |
Released May 19, 1999. Copyright 1997-1999, Theo de Raadt. ! ISBN - 0-9683637-3-3.
|
Following this are the instructions which you would have on a piece of paper if you had purchased a CDROM set instead of doing an alternate form of install. The instructions for doing an ftp (or other style *************** *** 59,83 **** Please refer to the following files on the two CDROMs for extensive details on how to install OpenBSD 2.5 on your machine:
!
Quick installer information for people familiar with OpenBSD, and the use of the new "disklabel -E" command. If you are at all confused when installing OpenBSD, read the relevant INSTALL.* file as listed above!
!
Play with your BIOS options, and see if you can enable booting off a CD; try using CD1. If not, write CD1:2.5/i386/floppy25.fs to a --- 71,100 ---- Please refer to the following files on the two CDROMs for extensive details on how to install OpenBSD 2.5 on your machine:
!
Quick installer information for people familiar with OpenBSD, and the use of the new "disklabel -E" command. If you are at all confused when installing OpenBSD, read the relevant INSTALL.* file as listed above!
!
Play with your BIOS options, and see if you can enable booting off a CD; try using CD1. If not, write CD1:2.5/i386/floppy25.fs to a *************** *** 90,96 **** be "floppy" or "rfd0c" or "rfd0a"). Use properly formatted perfect floppies with NO BAD BLOCKS or you will lose.
!
To boot off CD1, type "boot cdrom 2.5/sparc/bsd.rd", or "b sd(0,6,0)2.5/sparc/bsd.rd" depending on your ROM version. --- 107,113 ---- be "floppy" or "rfd0c" or "rfd0a"). Use properly formatted perfect floppies with NO BAD BLOCKS or you will lose.
!
To boot off CD1, type "boot cdrom 2.5/sparc/bsd.rd", or "b sd(0,6,0)2.5/sparc/bsd.rd" depending on your ROM version. *************** *** 103,120 **** the "kc.fs" floppy. This time, when the floppy is ejected simply re-insert "kc.fs" again and answer a different set of questions.
!
Create BSD partitions according to INSTALL.amiga's preparation section. Mount the CD2 under AmigaOS as device CD0: Next, execute the following CLI command: "CD0:2.5/amiga/utils/loadbsd CD0:2.5/amiga/bsd.rd".
!
You can boot over the network by following the instructions in INSTALL.hp300.
!
Your alpha must use SRM firmware (not ARC). If you have a CDROM, you can try "boot -fi 2.5/alpha/bsd.rd dkaX" (use "show device" to find your --- 120,137 ---- the "kc.fs" floppy. This time, when the floppy is ejected simply re-insert "kc.fs" again and answer a different set of questions.
!
Create BSD partitions according to INSTALL.amiga's preparation section. Mount the CD2 under AmigaOS as device CD0: Next, execute the following CLI command: "CD0:2.5/amiga/utils/loadbsd CD0:2.5/amiga/bsd.rd".
!
You can boot over the network by following the instructions in INSTALL.hp300.
!
Your alpha must use SRM firmware (not ARC). If you have a CDROM, you can try "boot -fi 2.5/alpha/bsd.rd dkaX" (use "show device" to find your *************** *** 122,128 **** floppy and boot that by typing "boot dva0". If this fails, you can place bsd.rd on some other device and boot it, or use the provided simpleroot.
!
Boot MacOS as normal and partition your disk with the appropriate A/UX configurations. Then, extract the Macside utilities from --- 139,145 ---- floppy and boot that by typing "boot dva0". If this fails, you can place bsd.rd on some other device and boot it, or use the provided simpleroot.
!
Boot MacOS as normal and partition your disk with the appropriate A/UX configurations. Then, extract the Macside utilities from *************** *** 131,139 **** BSD/Mac68k Installer to copy all the sets in CD1:2.5/mac68k/ onto your partitions. Finally, you will be ready to configure the BSD/Mac68k Booter with the location of your kernel and boot the system.
-
src.tar.gz contains a source archive starting at /usr/src. This file contains everything you need except for the kernel sources, which are in a separate archive. To extract: --- 148,158 ---- BSD/Mac68k Installer to copy all the sets in CD1:2.5/mac68k/ onto your partitions. Finally, you will be ready to configure the BSD/Mac68k Booter with the location of your kernel and boot the system. +
src.tar.gz contains a source archive starting at /usr/src. This file contains everything you need except for the kernel sources, which are in a separate archive. To extract: *************** *** 160,170 **** Using these files results in a much faster initial CVS update than you could expect from a fresh checkout of the full OpenBSD source tree. !
-
A ports tree archive is also provided. To extract:
--- 179,192 ---- Using these files results in a much faster initial CVS update than you could expect from a fresh checkout of the full OpenBSD source tree. !
A ports tree archive is also provided. To extract:
*************** *** 213,218 **** interested in seeing a port added, would like to help out, or just would like to know more, the mailing list ports@openbsd.org is a good place to know. ! ! ! --- 235,238 ---- interested in seeing a port added, would like to help out, or just would like to know more, the mailing list ports@openbsd.org is a good place to know. !