=================================================================== RCS file: /cvsrepo/anoncvs/cvs/www/25.html,v retrieving revision 1.28 retrieving revision 1.29 diff -u -r1.28 -r1.29 --- www/25.html 2016/08/15 02:22:05 1.28 +++ www/25.html 2019/05/27 22:55:18 1.29 @@ -1,37 +1,48 @@ - - - + + + + OpenBSD 2.5 - - - + + +

+[OpenBSD] -OpenBSD -2.5 +OpenBSD +2.5

-

+ + +
- -

+CD 2.5 +

 Released May 19, 1999.
Copyright 1997-1999, Theo de Raadt.
-ISBN - 0-9683637-3-3. +ISBN - 0-9683637-3-3.

  • Order a CDROM from our ordering system.
  • See the information on The FTP page for a list of mirror machines -
  • Go to the pub/OpenBSD/2.5/ directory on +
  • Go to the pub/OpenBSD/2.5/ directory on one of the mirror sites
  • Have a look at The 2.5 Errata page for a list of bugs and workarounds. @@ -40,13 +51,14 @@ All applicable copyrights and credits are in the src.tar.gz, sys.tar.gz, xenocara.tar.gz, ports.tar.gz files, or in the files fetched via ports.tar.gz. -
    +

- + +
+

How to install

+

-

How to install

-

Following this are the instructions which you would have on a piece of paper if you had purchased a CDROM set instead of doing an alternate form of install. The instructions for doing an ftp (or other style @@ -59,25 +71,30 @@ Please refer to the following files on the two CDROMs for extensive details on how to install OpenBSD 2.5 on your machine:

-

+ + +
+ +
+ +

Quick installer information for people familiar with OpenBSD, and the use of the new "disklabel -E" command. If you are at all confused when installing OpenBSD, read the relevant INSTALL.* file as listed above!

-

i386:

+

i386:

Play with your BIOS options, and see if you can enable booting off a CD; try using CD1. If not, write CD1:2.5/i386/floppy25.fs to a @@ -90,7 +107,7 @@ be "floppy" or "rfd0c" or "rfd0a"). Use properly formatted perfect floppies with NO BAD BLOCKS or you will lose.

-

SPARC:

+

SPARC:

To boot off CD1, type "boot cdrom 2.5/sparc/bsd.rd", or "b sd(0,6,0)2.5/sparc/bsd.rd" depending on your ROM version. @@ -103,18 +120,18 @@ the "kc.fs" floppy. This time, when the floppy is ejected simply re-insert "kc.fs" again and answer a different set of questions.

-

AMIGA:

+

AMIGA:

Create BSD partitions according to INSTALL.amiga's preparation section. Mount the CD2 under AmigaOS as device CD0: Next, execute the following CLI command: "CD0:2.5/amiga/utils/loadbsd CD0:2.5/amiga/bsd.rd".

-

HP300:

+

HP300:

You can boot over the network by following the instructions in INSTALL.hp300.

-

ALPHA:

+

ALPHA:

Your alpha must use SRM firmware (not ARC). If you have a CDROM, you can try "boot -fi 2.5/alpha/bsd.rd dkaX" (use "show device" to find your @@ -122,7 +139,7 @@ floppy and boot that by typing "boot dva0". If this fails, you can place bsd.rd on some other device and boot it, or use the provided simpleroot.

-

MAC68K:

+

MAC68K:

Boot MacOS as normal and partition your disk with the appropriate A/UX configurations. Then, extract the Macside utilities from @@ -131,9 +148,11 @@ BSD/Mac68k Installer to copy all the sets in CD1:2.5/mac68k/ onto your partitions. Finally, you will be ready to configure the BSD/Mac68k Booter with the location of your kernel and boot the system. +

+ +
+

NOTES ABOUT THE SOURCE CODE:

-

NOTES ABOUT THE SOURCE CODE:

-

src.tar.gz contains a source archive starting at /usr/src. This file contains everything you need except for the kernel sources, which are in a separate archive. To extract: @@ -160,11 +179,14 @@ Using these files results in a much faster initial CVS update than you could expect from a fresh checkout of the full OpenBSD source tree. -

+

+
+
+ +
+

PORTS TREE

-

PORTS TREE

-

A ports tree archive is also provided. To extract: 

@@ -213,6 +235,4 @@
 interested in seeing a port added, would like to help out, or just
 would like to know more, the mailing list ports@openbsd.org is a good
 place to know.
-
-
-
+