===================================================================
RCS file: /cvsrepo/anoncvs/cvs/www/25.html,v
retrieving revision 1.30
retrieving revision 1.31
diff -u -r1.30 -r1.31
--- www/25.html	2019/06/12 20:57:16	1.30
+++ www/25.html	2019/06/13 05:33:57	1.31
@@ -29,13 +29,13 @@
 Released May 19, 1999.<br>
 Copyright 1997-1999, Theo de Raadt.<br>
 <cite class=isbn>ISBN - 0-9683637-3-3</cite>.
-<p>
+
 <ul>
 <li>See the information on <a href=ftp.html>The FTP page</a> for
 	a list of mirror machines
 <li>Go to the <code class=reldir>pub/OpenBSD/2.5/</code> directory on
 	one of the mirror sites
-<li>Have a look at <a href=errata25.html>The 2.5 Errata page</a> for a list
+<li>Have a look at <a href="errata25.html">The 2.5 Errata page</a> for a list
 of bugs and workarounds.
 </ul>
 <p>
@@ -55,12 +55,11 @@
 of) install are very similar; the CDROM instructions are left intact
 so that you can see how much easier it would have been if you had
 purchased a CDROM instead.
-<p>
 
 <hr>
 Please refer to the following files on the two CDROMs for extensive
 details on how to install OpenBSD 2.5 on your machine:
-<p>
+
 <ul>
 <li><a href="https://ftp.openbsd.org/pub/OpenBSD/2.5/i386/INSTALL.i386">
 	.../OpenBSD/2.5/i386/INSTALL.i386 (on CD1)</a>
@@ -90,7 +89,7 @@
 Quick installer information for people familiar with OpenBSD, and the
 use of the new "disklabel -E" command.  If you are at all confused when
 installing OpenBSD, read the relevant INSTALL.* file as listed above!
-<p>
+
 <h3>OpenBSD/i386:</h3>
 <p>
 Play with your BIOS options, and see if you can enable booting off a
@@ -103,7 +102,7 @@
 Unix, use "dd if=&lt;file&gt; of=/dev/&lt;device&gt; bs=32k" (where device could
 be "floppy" or "rfd0c" or "rfd0a").  Use properly formatted perfect
 floppies with NO BAD BLOCKS or you will lose.
-<p>
+
 <h3>OpenBSD/sparc:</h3>
 <p>
 To boot off CD1, type "boot cdrom 2.5/sparc/bsd.rd", or
@@ -116,18 +115,18 @@
 floppy, insert "inst.fs".  Answer a bunch of questions.  Reboot from
 the "kc.fs" floppy.  This time, when the floppy is ejected simply
 re-insert "kc.fs" again and answer a different set of questions.
-<p>
+
 <h3>OpenBSD/amiga:</h3>
 <p>
 Create BSD partitions according to INSTALL.amiga's preparation section.
 Mount the CD2 under AmigaOS as device CD0: Next, execute the following
 CLI command: "CD0:2.5/amiga/utils/loadbsd CD0:2.5/amiga/bsd.rd".
-<p>
+
 <h3>OpenBSD/hp300:</h3>
 <p>
 You can boot over the network by following the instructions in
 INSTALL.hp300.
-<p>
+
 <h3>OpenBSD/alpha:</h3>
 <p>
 Your alpha must use SRM firmware (not ARC).  If you have a CDROM, you
@@ -135,7 +134,7 @@
 CDROM drive identifier). Otherwise, write CD2:2.5/alpha/floppy.fs to a
 floppy and boot that by typing "boot dva0".  If this fails, you can place
 bsd.rd on some other device and boot it, or use the provided simpleroot.
-<p>
+
 <h3>OpenBSD/mac68k:</h3>
 <p>
 Boot MacOS as normal and partition your disk with the appropriate A/UX
@@ -155,7 +154,6 @@
 src.tar.gz contains a source archive starting at /usr/src.  This file
 contains everything you need except for the kernel sources, which are
 in a separate archive.  To extract:
-<p>
 <blockquote><pre>
 # <kbd>mkdir -p /usr/src</kbd>
 # <kbd>cd /usr/src</kbd>
@@ -165,7 +163,6 @@
 srcsys.tar.gz contains a source archive starting at /usr/src/sys.
 This file contains all the kernel sources you need to rebuild kernels.
 To extract:
-<p>
 <blockquote><pre>
 # <kbd>mkdir -p /usr/src/sys</kbd>
 # <kbd>cd /usr/src</kbd>
@@ -186,7 +183,6 @@
 <h3>Ports Tree</h3>
 <p>
 A ports tree archive is also provided.  To extract:
-<p>
 <blockquote><pre>
 # <kbd>cd /usr</kbd>
 # <kbd>tar xvfz /tmp/ports.tar.gz</kbd>
@@ -196,7 +192,7 @@
 </pre></blockquote>
 <p>
 The ports/ subdirectory is a checkout of the OpenBSD ports tree.  Go
-read <a href=faq/faq15.html>http://www.OpenBSD.org/faq/faq15.html</a>
+read <a href="faq/faq15.html">https://www.OpenBSD.org/faq/faq15.html</a>
 if you know nothing about ports
 at this point.  This text is not a manual of how to use ports.
 Rather, it is a set of notes meant to kickstart the user on the
@@ -216,7 +212,6 @@
 order to keep current with it, you must make the ports/ tree
 available on a read-write medium and update the tree with a command
 like:
-<p>
 <blockquote><pre>
 # <kbd>cd [portsdir]/; cvs -d anoncvs@server.openbsd.org:/cvs update -Pd</kbd>
 </pre></blockquote>