=================================================================== RCS file: /cvsrepo/anoncvs/cvs/www/26.html,v retrieving revision 1.32 retrieving revision 1.33 diff -c -r1.32 -r1.33 *** www/26.html 2019/06/12 20:57:16 1.32 --- www/26.html 2019/06/13 05:33:57 1.33 *************** *** 22,34 ****
pub/OpenBSD/2.6/
directory on
one of the mirror sites
! --- 22,34 ----
pub/OpenBSD/2.6/
directory on
one of the mirror sites
! *************** *** 45,51 **** This is a partial list of new features and systems included in OpenBSD 2.6. For a comprehensive list, see the changelog leading to 2.6. -
Play with your BIOS options, and see if you can enable booting off a --- 133,139 ---- Quick installer information for people familiar with OpenBSD, and the use of the new "disklabel -E" command. If you are at all confused when installing OpenBSD, read the relevant INSTALL.* file as listed above! !
Play with your BIOS options, and see if you can enable booting off a *************** *** 148,154 **** Unix, use "dd if=<file> of=/dev/<device> bs=32k" (where device could be "floppy" or "rfd0c" or "rfd0a"). Use properly formatted perfect floppies with NO BAD BLOCKS or you will lose. !
To boot off CD1, type "boot cdrom 2.6/sparc/bsd.rd", or --- 146,152 ---- Unix, use "dd if=<file> of=/dev/<device> bs=32k" (where device could be "floppy" or "rfd0c" or "rfd0a"). Use properly formatted perfect floppies with NO BAD BLOCKS or you will lose. !
To boot off CD1, type "boot cdrom 2.6/sparc/bsd.rd", or *************** *** 161,178 **** floppy, insert "inst.fs". Answer a bunch of questions. Reboot from the "kc.fs" floppy. This time, when the floppy is ejected simply re-insert "kc.fs" again and answer a different set of questions. !
Create BSD partitions according to INSTALL.amiga's preparation section. Mount the CD2 under AmigaOS as device CD0: Next, execute the following CLI command: "CD0:2.6/amiga/utils/loadbsd CD0:2.6/amiga/bsd.rd". !
You can boot over the network by following the instructions in INSTALL.hp300. !
Your alpha must use SRM firmware (not ARC). If you have a CDROM, you --- 159,176 ---- floppy, insert "inst.fs". Answer a bunch of questions. Reboot from the "kc.fs" floppy. This time, when the floppy is ejected simply re-insert "kc.fs" again and answer a different set of questions. !
Create BSD partitions according to INSTALL.amiga's preparation section. Mount the CD2 under AmigaOS as device CD0: Next, execute the following CLI command: "CD0:2.6/amiga/utils/loadbsd CD0:2.6/amiga/bsd.rd". !
You can boot over the network by following the instructions in INSTALL.hp300. !
Your alpha must use SRM firmware (not ARC). If you have a CDROM, you *************** *** 180,186 **** CDROM drive identifier). Otherwise, write CD2:2.6/alpha/floppy.fs to a floppy and boot that by typing "boot dva0". If this fails, you can place bsd.rd on some other device and boot it, or use the provided simpleroot. !
Boot MacOS as normal and partition your disk with the appropriate A/UX --- 178,184 ---- CDROM drive identifier). Otherwise, write CD2:2.6/alpha/floppy.fs to a floppy and boot that by typing "boot dva0". If this fails, you can place bsd.rd on some other device and boot it, or use the provided simpleroot. !
Boot MacOS as normal and partition your disk with the appropriate A/UX *************** *** 200,206 **** src.tar.gz contains a source archive starting at /usr/src. This file contains everything you need except for the kernel sources, which are in a separate archive. To extract: -
# mkdir -p /usr/src # cd /usr/src --- 198,203 ---- *************** *** 210,216 **** srcsys.tar.gz contains a source archive starting at /usr/src/sys. This file contains all the kernel sources you need to rebuild kernels. To extract: -
# mkdir -p /usr/src/sys # cd /usr/src --- 207,212 ---- *************** *** 231,237 ****Ports Tree
A ports tree archive is also provided. To extract: -
# cd /usr # tar xvfz /tmp/ports.tar.gz --- 227,232 ---- *************** *** 241,247 ****The ports/ subdirectory is a checkout of the OpenBSD ports tree. Go ! read http://www.OpenBSD.org/faq/faq15.html if you know nothing about ports at this point. This text is not a manual of how to use ports. Rather, it is a set of notes meant to kickstart the user on the --- 236,242 ----
The ports/ subdirectory is a checkout of the OpenBSD ports tree. Go ! read https://www.OpenBSD.org/faq/faq15.html if you know nothing about ports at this point. This text is not a manual of how to use ports. Rather, it is a set of notes meant to kickstart the user on the *************** *** 261,267 **** order to keep current with it, you must make the ports/ tree available on a read-write medium and update the tree with a command like: -
--- 256,261 ----# cd [portsdir]/; cvs -d anoncvs@server.openbsd.org:/cvs update -Pd