-
+
+
Copyright 1997-1999, Theo de Raadt.
@@ -29,11 +37,11 @@
- ISBN 0-9683637-4-1. + ISBN 0-9683637-4-1. -->
pub/OpenBSD/2.6/ directory on
one of the mirror sites
+
|
-
-
+ |
Released December 1, 1999. Copyright 1997-1999, Theo de Raadt. @@ -29,11 +37,11 @@ - ISBN 0-9683637-4-1. + ISBN 0-9683637-4-1. --> pub/OpenBSD/2.6/ directory on
one of the mirror sites
+ |
-
Following this are the instructions which you would have on a piece of paper if you had purchased a CDROM set instead of doing an alternate form of install. The instructions for doing an ftp (or other style @@ -60,24 +69,29 @@ Please refer to the following files on the two CDROMs for extensive details on how to install OpenBSD 2.6 on your machine:
-
+
+
Quick installer information for people familiar with OpenBSD, and the use of the new "disklabel -E" command. If you are at all confused when installing OpenBSD, read the relevant INSTALL.* file as listed above!
-
Play with your BIOS options, and see if you can enable booting off a CD; try using CD1. If not, write CD1:2.6/i386/floppy26.fs to a @@ -90,7 +104,7 @@ be "floppy" or "rfd0c" or "rfd0a"). Use properly formatted perfect floppies with NO BAD BLOCKS or you will lose.
-
To boot off CD1, type "boot cdrom 2.6/sparc/bsd.rd", or "b sd(0,6,0)2.6/sparc/bsd.rd" depending on your ROM version. @@ -103,18 +117,18 @@ the "kc.fs" floppy. This time, when the floppy is ejected simply re-insert "kc.fs" again and answer a different set of questions.
-
Create BSD partitions according to INSTALL.amiga's preparation section. Mount the CD2 under AmigaOS as device CD0: Next, execute the following CLI command: "CD0:2.6/amiga/utils/loadbsd CD0:2.6/amiga/bsd.rd".
-
You can boot over the network by following the instructions in INSTALL.hp300.
-
Your alpha must use SRM firmware (not ARC). If you have a CDROM, you can try "boot -fi 2.6/alpha/bsd.rd dkaX" (use "show device" to find your @@ -122,7 +136,7 @@ floppy and boot that by typing "boot dva0". If this fails, you can place bsd.rd on some other device and boot it, or use the provided simpleroot.
-
Boot MacOS as normal and partition your disk with the appropriate A/UX configurations. Then, extract the Macside utilities from @@ -131,9 +145,11 @@ BSD/Mac68k Installer to copy all the sets in CD1:2.6/mac68k/ onto your partitions. Finally, you will be ready to configure the BSD/Mac68k Booter with the location of your kernel and boot the system. +
-
src.tar.gz contains a source archive starting at /usr/src. This file contains everything you need except for the kernel sources, which are in a separate archive. To extract: @@ -160,11 +176,14 @@ Using these files results in a much faster initial CVS update than you could expect from a fresh checkout of the full OpenBSD source tree. -
+
-
A ports tree archive is also provided. To extract:
@@ -213,12 +232,14 @@ interested in seeing a port added, would like to help out, or just would like to know more, the mailing list ports@openbsd.org is a good place to know. +
-
This is a partial list of new features and systems included in OpenBSD 2.6. For a comprehensive list, see the changelog leading to 2.6. @@ -266,7 +287,4 @@
- - - +