=================================================================== RCS file: /cvsrepo/anoncvs/cvs/www/26.html,v retrieving revision 1.31 retrieving revision 1.32 diff -u -r1.31 -r1.32 --- www/26.html 2019/05/27 22:55:18 1.31 +++ www/26.html 2019/06/12 20:57:16 1.32 @@ -7,16 +7,7 @@ - -
pub/OpenBSD/2.6/
directory on
@@ -54,9 +39,62 @@
+This is a partial list of new features and systems included in OpenBSD 2.6. +For a comprehensive list, see the changelog leading +to 2.6. +
+ +
Following this are the instructions which you would have on a piece of paper if you had purchased a CDROM set instead of doing an alternate @@ -65,23 +103,30 @@ so that you can see how much easier it would have been if you had purchased a CDROM instead.
+
+
+
-
Play with your BIOS options, and see if you can enable booting off a CD; try using CD1. If not, write CD1:2.6/i386/floppy26.fs to a @@ -104,7 +149,7 @@ be "floppy" or "rfd0c" or "rfd0a"). Use properly formatted perfect floppies with NO BAD BLOCKS or you will lose.
-
To boot off CD1, type "boot cdrom 2.6/sparc/bsd.rd", or "b sd(0,6,0)2.6/sparc/bsd.rd" depending on your ROM version. @@ -117,18 +162,18 @@ the "kc.fs" floppy. This time, when the floppy is ejected simply re-insert "kc.fs" again and answer a different set of questions.
-
Create BSD partitions according to INSTALL.amiga's preparation section. Mount the CD2 under AmigaOS as device CD0: Next, execute the following CLI command: "CD0:2.6/amiga/utils/loadbsd CD0:2.6/amiga/bsd.rd".
-
You can boot over the network by following the instructions in INSTALL.hp300.
-
Your alpha must use SRM firmware (not ARC). If you have a CDROM, you can try "boot -fi 2.6/alpha/bsd.rd dkaX" (use "show device" to find your @@ -136,7 +181,7 @@ floppy and boot that by typing "boot dva0". If this fails, you can place bsd.rd on some other device and boot it, or use the provided simpleroot.
-
Boot MacOS as normal and partition your disk with the appropriate A/UX configurations. Then, extract the Macside utilities from @@ -147,52 +192,53 @@ Booter with the location of your kernel and boot the system. +
src.tar.gz contains a source archive starting at /usr/src. This file contains everything you need except for the kernel sources, which are in a separate archive. To extract:
-
-# mkdir -p /usr/src -# cd /usr/src -# tar xvfz /tmp/src.tar.gz -+
+# mkdir -p /usr/src +# cd /usr/src +# tar xvfz /tmp/src.tar.gz +
srcsys.tar.gz contains a source archive starting at /usr/src/sys. This file contains all the kernel sources you need to rebuild kernels. To extract:
-
-# mkdir -p /usr/src/sys -# cd /usr/src -# tar xvfz /tmp/srcsys.tar.gz -+
+# mkdir -p /usr/src/sys +# cd /usr/src +# tar xvfz /tmp/srcsys.tar.gz +
Both of these trees are a regular CVS checkout. Using these trees it is possible to get a head-start on using the anoncvs servers as -described at http://www.OpenBSD.org/anoncvs.html. +described here. Using these files results in a much faster initial CVS update than you could expect from a fresh checkout of the full OpenBSD source tree.
A ports tree archive is also provided. To extract:
-
-# cd /usr -# tar xvfz /tmp/ports.tar.gz -# cd ports -# ls ++# cd /usr +# tar xvfz /tmp/ports.tar.gz +# cd ports +# ls ... -+
The ports/ subdirectory is a checkout of the OpenBSD ports tree. Go read http://www.OpenBSD.org/faq/faq15.html @@ -216,9 +262,9 @@ available on a read-write medium and update the tree with a command like:
-
-# cd [portsdir]/; cvs -d anoncvs@server.openbsd.org:/cvs update -Pd -+
+# cd [portsdir]/; cvs -d anoncvs@server.openbsd.org:/cvs update -Pd +
[Of course, you must replace the local directory and server name here with the location of your ports collection and a nearby anoncvs @@ -232,59 +278,4 @@ interested in seeing a port added, would like to help out, or just would like to know more, the mailing list ports@openbsd.org is a good place to know. -
-This is a partial list of new features and systems included in OpenBSD 2.6. -For a comprehensive list, see the changelog leading -to 2.6. -
- -