===================================================================
RCS file: /cvsrepo/anoncvs/cvs/www/27.html,v
retrieving revision 1.41
retrieving revision 1.42
diff -c -r1.41 -r1.42
*** www/27.html 2019/06/12 20:57:16 1.41
--- www/27.html 2019/06/13 05:33:57 1.42
***************
*** 23,35 ****
Released June 15, 2000.
Copyright 1997-2000, Theo de Raadt.
ISBN 0-9683637-5-X
!
pub/OpenBSD/2.7/
directory on
one of the mirror sites
! pub/OpenBSD/2.7/
directory on
one of the mirror sites
!
Play with your BIOS options, and see if you can enable booting off a --- 235,241 ---- Quick installer information for people familiar with OpenBSD, and the use of the new "disklabel -E" command. If you are at all confused when installing OpenBSD, read the relevant INSTALL.* file as listed above! !
Play with your BIOS options, and see if you can enable booting off a *************** *** 250,256 **** Unix, use "dd if=<file> of=/dev/<device> bs=32k" (where device could be "floppy" or "rfd0c" or "rfd0a"). Use properly formatted perfect floppies with NO BAD BLOCKS or you will lose. !
To boot off CD2, type "boot cdrom 2.7/sparc/bsd.rd", or --- 248,254 ---- Unix, use "dd if=<file> of=/dev/<device> bs=32k" (where device could be "floppy" or "rfd0c" or "rfd0a"). Use properly formatted perfect floppies with NO BAD BLOCKS or you will lose. !
To boot off CD2, type "boot cdrom 2.7/sparc/bsd.rd", or *************** *** 263,280 **** floppy, insert "inst.fs". Answer a bunch of questions. Reboot from the "kc.fs" floppy. This time, when the floppy is ejected simply re-insert "kc.fs" again and answer a different set of questions. !
Create BSD partitions according to INSTALL.amiga's preparation section. Mount the CD2 under AmigaOS as device CD0: Next, execute the following CLI command: "CD0:2.7/amiga/utils/loadbsd CD0:2.7/amiga/bsd.rd". !
You can boot over the network by following the instructions in INSTALL.hp300. !
Boot MacOS as normal and partition your disk with the appropriate A/UX --- 261,278 ---- floppy, insert "inst.fs". Answer a bunch of questions. Reboot from the "kc.fs" floppy. This time, when the floppy is ejected simply re-insert "kc.fs" again and answer a different set of questions. !
Create BSD partitions according to INSTALL.amiga's preparation section. Mount the CD2 under AmigaOS as device CD0: Next, execute the following CLI command: "CD0:2.7/amiga/utils/loadbsd CD0:2.7/amiga/bsd.rd". !
You can boot over the network by following the instructions in INSTALL.hp300. !
Boot MacOS as normal and partition your disk with the appropriate A/UX *************** *** 284,290 **** BSD/Mac68k Installer to copy all the sets in CD1:2.7/mac68k/ onto your partitions. Finally, you will be ready to configure the BSD/Mac68k Booter with the location of your kernel and boot the system. !
Get the release via ftp. Then, you can either setup a diskless boot or --- 282,288 ---- BSD/Mac68k Installer to copy all the sets in CD1:2.7/mac68k/ onto your partitions. Finally, you will be ready to configure the BSD/Mac68k Booter with the location of your kernel and boot the system. !
Get the release via ftp. Then, you can either setup a diskless boot or *************** *** 299,305 **** src.tar.gz contains a source archive starting at /usr/src. This file contains everything you need except for the kernel sources, which are in a separate archive. To extract: -
# mkdir -p /usr/src # cd /usr/src --- 297,302 ---- *************** *** 309,315 **** srcsys.tar.gz contains a source archive starting at /usr/src/sys. This file contains all the kernel sources you need to rebuild kernels. To extract: -
# mkdir -p /usr/src/sys # cd /usr/src --- 306,311 ---- *************** *** 330,336 ****Ports Tree
A ports tree archive is also provided. To extract: -
# cd /usr # tar xvfz /tmp/ports.tar.gz --- 326,331 ---- *************** *** 340,346 ****The ports/ subdirectory is a checkout of the OpenBSD ports tree. Go ! read http://www.OpenBSD.org/faq/faq15.html if you know nothing about ports at this point. This text is not a manual of how to use ports. Rather, it is a set of notes meant to kickstart the user on the --- 335,341 ----
The ports/ subdirectory is a checkout of the OpenBSD ports tree. Go ! read https://www.OpenBSD.org/faq/faq15.html if you know nothing about ports at this point. This text is not a manual of how to use ports. Rather, it is a set of notes meant to kickstart the user on the *************** *** 360,366 **** order to keep current with it, you must make the ports/ tree available on a read-write medium and update the tree with a command like: -
--- 355,360 ----# cd [portsdir]/; cvs -d anoncvs@server.openbsd.org:/cvs update -Pd