pub/OpenBSD/2.8/ directory on
--- 25,30 ----
***************
*** 56,62 ****
This is a partial list of new features and systems included in OpenBSD 2.8.
For a comprehensive list, see the changelog leading
--- 44,49 ----
***************
*** 145,151 ****
Following this are the instructions which you would have on a piece of
paper if you had purchased a CDROM set instead of doing an alternate
--- 132,137 ----
***************
*** 160,181 ****
details on how to install OpenBSD 2.8 on your machine:
!
! How to install
-
!
!
!
!
!
--- 146,175 ----
details on how to install OpenBSD 2.8 on your machine:
!
!
!
Play with your BIOS options, and see if you can enable booting off a CD; try using CD1. If not, write CD1:2.8/i386/floppy28.fs to a --- 179,185 ---- use of the new "disklabel -E" command. If you are at all confused when installing OpenBSD, read the relevant INSTALL.* file as listed above!
!
Play with your BIOS options, and see if you can enable booting off a CD; try using CD1. If not, write CD1:2.8/i386/floppy28.fs to a *************** *** 206,230 **** config(8) after a successful boot for instructions on how to re-write your kernel to disable pcibios(4) permanently.
!
To boot off CD2, type "boot cdrom 2.8/sparc/bsd.rd", or "b sd(0,6,0)2.8/sparc/bsd.rd" depending on your ROM version. Alternatively, write CD2:2.8/sparc/floppy28.fs to a floppy and boot it using "boot floppy" or "boot fd()" depending on your ROM version.
!
Create BSD partitions according to INSTALL.amiga's preparation section. Mount the CD2 under AmigaOS as device CD0: Next, execute the following CLI command: "CD0:2.8/amiga/utils/loadbsd CD0:2.8/amiga/bsd.rd".
!
You can boot over the network by following the instructions in INSTALL.hp300.
!
Boot MacOS as normal and partition your disk with the appropriate A/UX configurations. Then, extract the Macside utilities from --- 200,224 ---- config(8) after a successful boot for instructions on how to re-write your kernel to disable pcibios(4) permanently.
!
To boot off CD2, type "boot cdrom 2.8/sparc/bsd.rd", or "b sd(0,6,0)2.8/sparc/bsd.rd" depending on your ROM version. Alternatively, write CD2:2.8/sparc/floppy28.fs to a floppy and boot it using "boot floppy" or "boot fd()" depending on your ROM version.
!
Create BSD partitions according to INSTALL.amiga's preparation section. Mount the CD2 under AmigaOS as device CD0: Next, execute the following CLI command: "CD0:2.8/amiga/utils/loadbsd CD0:2.8/amiga/bsd.rd".
!
You can boot over the network by following the instructions in INSTALL.hp300.
!
Boot MacOS as normal and partition your disk with the appropriate A/UX configurations. Then, extract the Macside utilities from *************** *** 234,276 **** partitions. Finally, you will be ready to configure the BSD/Mac68k Booter with the location of your kernel and boot the system.
!
Get the release via ftp. Then, you can either setup a diskless boot or create an installation tape, as described in INSTALL.sun3.
src.tar.gz contains a source archive starting at /usr/src. This file contains everything you need except for the kernel sources, which are in a separate archive. To extract:
!
! # mkdir -p /usr/src ! # cd /usr/src ! # tar xvfz /tmp/src.tar.gz !
srcsys.tar.gz contains a source archive starting at /usr/src/sys. This file contains all the kernel sources you need to rebuild kernels. To extract:
!
! # mkdir -p /usr/src/sys ! # cd /usr/src ! # tar xvfz /tmp/srcsys.tar.gz !
Both of these trees are a regular CVS checkout. Using these trees it is possible to get a head-start on using the anoncvs servers as ! described at http://www.OpenBSD.org/anoncvs.html. Using these files results in a much faster initial CVS update than you could expect from a fresh checkout of the full OpenBSD source tree.
!
Get the release via ftp. Then, you can either setup a diskless boot or create an installation tape, as described in INSTALL.sun3. +
src.tar.gz contains a source archive starting at /usr/src. This file contains everything you need except for the kernel sources, which are in a separate archive. To extract:
!
! # mkdir -p /usr/src ! # cd /usr/src ! # tar xvfz /tmp/src.tar.gz !
srcsys.tar.gz contains a source archive starting at /usr/src/sys. This file contains all the kernel sources you need to rebuild kernels. To extract:
!
! # mkdir -p /usr/src/sys ! # cd /usr/src ! # tar xvfz /tmp/srcsys.tar.gz !
Both of these trees are a regular CVS checkout. Using these trees it is possible to get a head-start on using the anoncvs servers as ! described here. Using these files results in a much faster initial CVS update than you could expect from a fresh checkout of the full OpenBSD source tree.
A ports tree archive is also provided. To extract:
!
! # cd /usr ! # tar xvfz /tmp/ports.tar.gz ! # cd ports ! # ls ... !
The ports/ subdirectory is a checkout of the OpenBSD ports tree. Go read http://www.OpenBSD.org/faq/faq15.html --- 274,286 ----
A ports tree archive is also provided. To extract:
!
! # cd /usr ! # tar xvfz /tmp/ports.tar.gz ! # cd ports ! # ls ... !
The ports/ subdirectory is a checkout of the OpenBSD ports tree. Go read http://www.OpenBSD.org/faq/faq15.html *************** *** 309,317 **** available on a read-write medium and update the tree with a command like:
!
! # cd [portsdir]/; cvs -d anoncvs@server.openbsd.org:/cvs update -Pd !
[Of course, you must replace the local directory and server name here with the location of your ports collection and a nearby anoncvs --- 304,312 ---- available on a read-write medium and update the tree with a command like:
!
! # cd [portsdir]/; cvs -d anoncvs@server.openbsd.org:/cvs update -Pd !
[Of course, you must replace the local directory and server name here with the location of your ports collection and a nearby anoncvs *************** *** 323,328 ****
Finally, despite ports' youth, help is never far. If you're interested in seeing a port added, would like to help out, or just ! would like to know more, the mailing list ports@openbsd.org is a good ! place to know. --- 318,323 ----
Finally, despite ports' youth, help is never far. If you're interested in seeing a port added, would like to help out, or just ! would like to know more, the mailing list ! ports@openbsd.org is a good place to know.