=================================================================== RCS file: /cvsrepo/anoncvs/cvs/www/28.html,v retrieving revision 1.32 retrieving revision 1.33 diff -u -r1.32 -r1.33 --- www/28.html 2018/06/12 15:20:28 1.32 +++ www/28.html 2019/05/27 22:55:18 1.33 @@ -1,29 +1,37 @@ - - - + + + + OpenBSD 2.8 - - - + -

+

-OpenBSD -2.8 +OpenBSD +2.8

+ + +
- -

+Manga Ramblo +

 Released December 1, 2000
Copyright 1997-2000, Theo de Raadt.
-ISBN 0-9683637-6-8 +ISBN 0-9683637-6-8

  • See the information on The FTP page for a list of mirror machines -
  • Go to the pub/OpenBSD/2.8/ directory on +
  • Go to the pub/OpenBSD/2.8/ directory on one of the mirror sites
  • Have a look at The 2.8 Errata page for a list of bugs and workarounds. @@ -42,13 +50,14 @@ All applicable copyrights and credits are in the src.tar.gz, sys.tar.gz, xenocara.tar.gz, ports.tar.gz files, or in the files fetched via ports.tar.gz. -
    +
- + +
+

What's New

+

-

What's New

-

This is a partial list of new features and systems included in OpenBSD 2.8. For a comprehensive list, see the changelog leading to 2.8. @@ -128,16 +137,16 @@

  • Import of tcfs, a file content crypto file system.
  • New sftp-server in OpenSSH. -

    -

    +

    • -
    + +
    +

    How to install

    +

    -

    How to install

    -

    Following this are the instructions which you would have on a piece of paper if you had purchased a CDROM set instead of doing an alternate form of install. The instructions for doing an ftp (or other style @@ -150,28 +159,33 @@ Please refer to the following files on the two CDROMs for extensive details on how to install OpenBSD 2.8 on your machine:

    -

    + + +
    + +
    + +

    Quick installer information for people familiar with OpenBSD, and the use of the new "disklabel -E" command. If you are at all confused when installing OpenBSD, read the relevant INSTALL.* file as listed above!

    -

    i386:

    +

    i386:

    Play with your BIOS options, and see if you can enable booting off a CD; try using CD1. If not, write CD1:2.8/i386/floppy28.fs to a @@ -185,32 +199,32 @@ floppies with NO BAD BLOCKS or you will lose.

    If you experience any boot hangs on PCI devices, or any panic early in boot -that seems related to pcibios(4), you might have to disable the pcibios device as +that seems related to pcibios(4), you might have to disable the pcibios device as a workaround. At the boot> prompt, type "boot -c" to enter User Kernel Configuration. At the UKC> prompt, enter "disable pcibios" then "quit". See -config(8) after a successful boot for instructions on how to re-write your kernel -to disable pcibios(4) permanently. +config(8) after a successful boot for instructions on how to re-write your kernel +to disable pcibios(4) permanently.

    -

    sparc:

    +

    sparc:

    To boot off CD2, type "boot cdrom 2.8/sparc/bsd.rd", or "b sd(0,6,0)2.8/sparc/bsd.rd" depending on your ROM version. Alternatively, write CD2:2.8/sparc/floppy28.fs to a floppy and boot it using "boot floppy" or "boot fd()" depending on your ROM version.

    -

    amiga:

    +

    amiga:

    Create BSD partitions according to INSTALL.amiga's preparation section. Mount the CD2 under AmigaOS as device CD0: Next, execute the following CLI command: "CD0:2.8/amiga/utils/loadbsd CD0:2.8/amiga/bsd.rd".

    -

    hp300:

    +

    hp300:

    You can boot over the network by following the instructions in INSTALL.hp300.

    -

    mac68k:

    +

    mac68k:

    Boot MacOS as normal and partition your disk with the appropriate A/UX configurations. Then, extract the Macside utilities from @@ -220,13 +234,15 @@ partitions. Finally, you will be ready to configure the BSD/Mac68k Booter with the location of your kernel and boot the system.

    -

    sun3:

    +

    sun3:

    Get the release via ftp. Then, you can either setup a diskless boot or create an installation tape, as described in INSTALL.sun3. +

    + +
    +

    Notes about the source code:

    -

    Notes about the source code:

    -

    src.tar.gz contains a source archive starting at /usr/src. This file contains everything you need except for the kernel sources, which are in a separate archive. To extract: @@ -253,13 +269,14 @@ Using these files results in a much faster initial CVS update than you could expect from a fresh checkout of the full OpenBSD source tree. -

    +

    +
    -
    + +
    +

    Ports Tree

    -

    Ports Tree

    -

    A ports tree archive is also provided. To extract: 

    @@ -308,7 +325,4 @@
 interested in seeing a port added, would like to help out, or just
 would like to know more, the mailing list ports@openbsd.org is a good
 place to know.
-
    
-
-
-
+