Following this are the instructions which you would have on a piece of
paper if you had purchased a CDROM set instead of doing an alternate
form of install. The instructions for doing an ftp (or other style
@@ -345,14 +360,16 @@
+
Quick installer information for people familiar with OpenBSD, and the
use of the "disklabel -E" command. If you are at all confused when
installing OpenBSD, read the relevant INSTALL.* file as listed above!
-
-
OpenBSD/i386:
-
+OpenBSD/i386:
+
+
Play with your BIOS options to enable booting from a CD. The OpenBSD/i386
release is on CD1. If your BIOS does not support booting from CD, you will need
to create a boot floppy to install from. To create a boot floppy write
@@ -369,52 +386,49 @@
To make a boot floppy under MS-DOS, use the "rawrite" utility located
at CD:/3.4/tools/rawrite.exe. To make the boot floppy under a Unix OS,
-use the dd(1) utility. The following is an example usage of
-dd(1)
+use the dd(1)
+utility. The following is an example usage of
+dd(1)
, where the device could be "floppy", "rfd0c", or
"rfd0a".
-
-# dd if=<file> of=/dev/<device> bs=32k
-
+
+# dd if=<file> of=/dev/<device> bs=32k
+
Make sure you use properly formatted perfect floppies with NO BAD BLOCKS or
your install will most likely fail. For more information on creating a boot
floppy and installing OpenBSD/i386 please refer to
this page.
-
+
OpenBSD/macppc:
+
-
OpenBSD/macppc:
-
Put the CD2 in your CDROM drive and poweron your machine while holding down the
C key until the display turns on and shows OpenBSD/macppc boot.
Alternatively, at the Open Firmware prompt, enter boot cd:,ofwboot
/3.4/macppc/bsd.rd
-
+OpenBSD/vax:
+
-
OpenBSD/vax:
-
Boot over the network via mopbooting as described in INSTALL.vax.
-
+OpenBSD/sparc:
+
-
OpenBSD/sparc:
-
The 3.4 release of OpenBSD/sparc is located on CD3. To boot off of this CD you
can use one of the two commands listed below, depending on the version of your
ROM.
-
-> boot cdrom 3.4/sparc/bsd.rd
+
+> boot cdrom 3.4/sparc/bsd.rd
or
-> b sd(0,6,0)3.4/sparc/bsd.rd
-
+> b sd(0,6,0)3.4/sparc/bsd.rd
+
If your sparc does not have a CD drive, you can alternatively boot from floppy.
@@ -423,11 +437,11 @@
the floppy use one of the two commands listed below, depending on the version of
your ROM.
-
-> boot floppy
+
+> boot floppy
or
-> boot fd()
-
+> boot fd()
+
Make sure you use a properly formatted floppy with NO BAD BLOCKS or your install
@@ -437,11 +451,10 @@
If your sparc doesn't have a floppy drive nor a CD drive, you can either
setup a bootable tape, or install via network, as told in the
INSTALL.sparc file.
-
+
OpenBSD/sparc64:
+
-
OpenBSD/sparc64:
-
Put the CD3 in your CDROM drive and type boot cdrom.
@@ -457,12 +470,11 @@
If nothing works, you can boot over the network as described in INSTALL.sparc64
-
+OpenBSD/alpha:
+
-
OpenBSD/alpha:
-
-Write FTP:3.4/alpha/floppy34.fs or
+Write FTP:3.4/alpha/floppy34.fs or
FTP:3.4/alpha/floppyB34.fs (depending on your machine) to a diskette and
enter boot dva0. Refer to INSTALL.alpha for more details.
@@ -470,27 +482,20 @@
Make sure you use a properly formatted floppy with NO BAD BLOCKS or your install
will most likely fail.
-
+OpenBSD/hp300:
-
OpenBSD/hp300:
-
+OpenBSD/hppa:
+
-
OpenBSD/hppa:
-
+OpenBSD/mac68k:
+
-
OpenBSD/mac68k:
-
-
Boot MacOS as normal and partition your disk with the appropriate A/UX
configurations. Then, extract the Macside utilities from
FTP:3.4/mac68k/utils onto your hard disk. Run Mkfs to create your
@@ -498,61 +503,65 @@
"BSD/Mac68k Installer" to copy all the sets in FTP:3.4/mac68k/ onto your
partitions. Finally, you will be ready to configure the "BSD/Mac68k
Booter" with the location of your kernel and boot the system.
-
+OpenBSD/mvme68k:
+
-
OpenBSD/mvme68k:
-
-
You can create a bootable installation tape or boot over the network.
The network boot requires a MVME68K BUG version that supports the NIOT
and NBO debugger commands. Follow the instructions in INSTALL.mvme68k
for more details.
-
+
+
+
+Notes about the source code:
+
-
Notes about the source code:
-
-# mkdir -p /usr/src
-# cd /usr/src
-# tar xvfz /tmp/src.tar.gz
-
-
sys.tar.gz contains a source archive starting at /usr/src/sys.
This file contains all the kernel sources you need to rebuild kernels.
To extract:
+
+
+# mkdir -p /usr/src/sys
+# cd /usr/src
+# tar xvfz /tmp/sys.tar.gz
+
+
-
-# mkdir -p /usr/src/sys
-# cd /usr/src
-# tar xvfz /tmp/sys.tar.gz
-
-
Both of these trees are a regular CVS checkout. Using these trees it
is possible to get a head-start on using the anoncvs servers as
described here.
Using these files
results in a much faster initial CVS update than you could expect from
a fresh checkout of the full OpenBSD source tree.
-
-
-
+
+
+
-