version 1.18, 2004/09/03 14:52:48 |
version 1.19, 2004/09/03 23:39:15 |
|
|
now supports nested anchors. |
now supports nested anchors. |
<li><a href="http://www.openbsd.org/cgi-bin/man.cgi?query=tcpdrop&sektion=8">tcpdrop(8)</a>, |
<li><a href="http://www.openbsd.org/cgi-bin/man.cgi?query=tcpdrop&sektion=8">tcpdrop(8)</a>, |
a command to drop TCP connections. |
a command to drop TCP connections. |
<li>The NMBCLUSTERS option has been eliminated, replaced by a sysctl with higher values on many platforms. |
<li>The NMBCLUSTERS option has been eliminated, replaced by a sysctl |
|
with higher default values on many platforms. |
<li>Added support for cksum (three flavours), md4, sha256, sha384 and sha512 to |
<li>Added support for cksum (three flavours), md4, sha256, sha384 and sha512 to |
the <a href="http://www.openbsd.org/cgi-bin/man.cgi?query=md5&sektion=1">md5(1)</a> |
the <a href="http://www.openbsd.org/cgi-bin/man.cgi?query=md5&sektion=1">md5(1)</a> |
command. |
command. |
|
|
<li>New <a href="http://www.openbsd.org/cgi-bin/man.cgi?query=atw&sektion=4">atw(4)</a> |
<li>New <a href="http://www.openbsd.org/cgi-bin/man.cgi?query=atw&sektion=4">atw(4)</a> |
driver for ADMtek ADM8211 802.11b wireless adapters. |
driver for ADMtek ADM8211 802.11b wireless adapters. |
<li>New <a href="http://www.openbsd.org/cgi-bin/man.cgi?query=axe&sektion=4">axe(4)</a> |
<li>New <a href="http://www.openbsd.org/cgi-bin/man.cgi?query=axe&sektion=4">axe(4)</a> |
driver for ASIX Electronics AX88172 USB Ethernet adaptors. |
driver for ASIX Electronics AX88172 USB Ethernet adapters. |
<li>New <a href="http://www.openbsd.org/cgi-bin/man.cgi?query=cdce&sektion=4">cdce(4)</a> |
<li>New <a href="http://www.openbsd.org/cgi-bin/man.cgi?query=cdce&sektion=4">cdce(4)</a> |
driver for Ethernet over USB bridges. |
driver for Ethernet over USB bridges. |
<li>New <a href="http://www.openbsd.org/cgi-bin/man.cgi?query=ichpcib&sektion=4&arch=i386">ichpcib(4)</a> |
<li>New <a href="http://www.openbsd.org/cgi-bin/man.cgi?query=ichpcib&sektion=4&arch=i386">ichpcib(4)</a> |
|
|
<ul> |
<ul> |
<li>Kernel memory management improvements now allow the full global |
<li>Kernel memory management improvements now allow the full global |
routing table to be kept in memory without customizing or tuning. |
routing table to be kept in memory without customizing or tuning. |
<li>Support for IPSEC, both manually keyed and using IKE. |
<li>Support for IPsec, both manually keyed and using IKE. |
<li>Support for NOPEER community (RFC3706). |
<li>Support for NOPEER community (RFC3706). |
<li>Partial support for RFC2858 Multiprotocol Capabilities, currently only |
<li>Partial support for RFC2858 Multiprotocol Capabilities, currently only |
IPv4-unicast is announced. |
IPv4-unicast is announced. |
|
|
</pre></ul> |
</pre></ul> |
|
|
<p> |
<p> |
If your sparc does not have a CD drive, you can alternatively boot from floppy. |
If your SPARC system does not have a CD drive, you can alternatively boot from floppy. |
To do so you need to write <i>CD3:3.6/sparc/floppy36.fs</i> to a floppy. |
To do so you need to write <i>CD3:3.6/sparc/floppy36.fs</i> to a floppy. |
For more information see <a href="faq/faq4.html#MkFlop">FAQ4.1</a>. To boot from |
For more information see <a href="faq/faq4.html#MkFlop">FAQ4.1</a>. To boot from |
the floppy use one of the two commands listed below, depending on the version of |
the floppy use one of the two commands listed below, depending on the version of |
|
|
will most likely fail. |
will most likely fail. |
|
|
<p> |
<p> |
If your sparc doesn't have a floppy drive nor a CD drive, you can either |
If your SPARC system doesn't have a floppy drive nor a CD drive, you can either |
setup a bootable tape, or install via network, as told in the |
setup a bootable tape, or install via network, as told in the |
INSTALL.sparc file. |
INSTALL.sparc file. |
</ul> |
</ul> |