This is a partial list of new features and systems included in OpenBSD 3.6.
For a comprehensive list, see the changelog leading
--- 48,53 ----
***************
*** 265,271 ****
Following this are the instructions which you would have on a piece of
paper if you had purchased a CDROM set instead of doing an alternate
--- 251,256 ----
***************
*** 280,303 ****
extensive details on how to install OpenBSD 3.6 on your machine:
!
!
!
!
!
!
! Write FTP:3.6/alpha/floppy36.fs or
! FTP:3.6/alpha/floppyB36.fs (depending on your machine) to a diskette and
enter boot dva0. Refer to INSTALL.alpha for more details.
--- 439,446 ----
! Write 3.6/alpha/floppy36.fs or
! 3.6/alpha/floppyB36.fs (depending on your machine) to a diskette and
enter boot dva0. Refer to INSTALL.alpha for more details.
***************
*** 450,456 ****
After updating the firmware to at least ABLE 1.95 if necessary, boot
! FTP:3.6/cats/bsd.rd from an ABLE-supported device (such as a CD-ROM
or an existing FFS or EXT2FS partition).
After updating the firmware to at least ABLE 1.95 if necessary, boot
! 3.6/cats/bsd.rd from an ABLE-supported device (such as a CD-ROM
or an existing FFS or EXT2FS partition).
Boot MacOS as normal and partition your disk with the appropriate A/UX
configurations. Then, extract the Macside utilities from
! FTP:3.6/mac68k/utils onto your hard disk. Run Mkfs to create your
filesystems on the A/UX partitions you just made. Then, use the
! "BSD/Mac68k Installer" to copy all the sets in FTP:3.6/mac68k/ onto your
partitions. Finally, you will be ready to configure the "BSD/Mac68k
Booter" with the location of your kernel and boot the system.
--- 477,485 ----
Boot MacOS as normal and partition your disk with the appropriate A/UX
configurations. Then, extract the Macside utilities from
! 3.6/mac68k/utils onto your hard disk. Run Mkfs to create your
filesystems on the A/UX partitions you just made. Then, use the
! "BSD/Mac68k Installer" to copy all the sets in 3.6/mac68k/ onto your
partitions. Finally, you will be ready to configure the "BSD/Mac68k
Booter" with the location of your kernel and boot the system.
***************
*** 497,508 ****
The network boot requires a MVME88K BUG version that supports the NIOT
and NBO debugger commands. Follow the instructions in INSTALL.mvme88k
for more details.
-
src.tar.gz contains a source archive starting at /usr/src. This file
contains everything you need except for the kernel sources, which are
--- 498,509 ----
The network boot requires a MVME88K BUG version that supports the NIOT
and NBO debugger commands. Follow the instructions in INSTALL.mvme88k
for more details.
src.tar.gz contains a source archive starting at /usr/src. This file
contains everything you need except for the kernel sources, which are
***************
*** 532,540 ****
Using these files
results in a much faster initial CVS update than you could expect from
a fresh checkout of the full OpenBSD source tree.
-
How to install
-
!
!
+
OpenBSD/alpha:
OpenBSD/alpha:
OpenBSD/hp300:
--- 451,457 ----
OpenBSD/hp300:
***************
*** 476,484 ****
Notes about the source code:
+ Notes about the source code
! Note that most ports are available as packages through ftp. Updated packages for the 3.6 release will be made available if problems arise.
If you're interested in seeing a port added, would like to help out, or just ! would like to know more, the mailing list ports@openbsd.org is a good ! place to know.
! Note that most ports are available as packages on our mirrors. Updated packages for the 3.6 release will be made available if problems arise.
If you're interested in seeing a port added, would like to help out, or just ! would like to know more, the mailing list ! ports@openbsd.org is a good place to know.