=================================================================== RCS file: /cvsrepo/anoncvs/cvs/www/37.html,v retrieving revision 1.86 retrieving revision 1.87 diff -c -r1.86 -r1.87 *** www/37.html 2019/05/27 22:55:18 1.86 --- www/37.html 2019/06/12 20:57:16 1.87 *************** *** 7,26 **** - -
This is a partial list of new features and systems included in OpenBSD 3.7.
For a comprehensive list, see the changelog leading
--- 48,53 ----
***************
*** 329,335 ****
Following this are the instructions which you would have on a piece of
paper if you had purchased a CDROM set instead of doing an alternate
--- 315,320 ----
***************
*** 344,369 ****
extensive details on how to install OpenBSD 3.7 on your machine:
!
!
!
!
!
!
! Write FTP:3.7/alpha/floppy37.fs or
! FTP:3.7/alpha/floppyB37.fs (depending on your machine) to a diskette and
enter boot dva0. Refer to INSTALL.alpha for more details.
--- 507,514 ----
! Write 3.7/alpha/floppy37.fs or
! 3.7/alpha/floppyB37.fs (depending on your machine) to a diskette and
enter boot dva0. Refer to INSTALL.alpha for more details.
***************
*** 516,522 ****
After updating the firmware to at least ABLE 1.95 if necessary, boot
! FTP:3.7/cats/bsd.rd from an ABLE-supported device (such as a CD-ROM
or an existing FFS or EXT2FS partition).
After updating the firmware to at least ABLE 1.95 if necessary, boot
! 3.7/cats/bsd.rd from an ABLE-supported device (such as a CD-ROM
or an existing FFS or EXT2FS partition).
Boot MacOS as normal and extract the Macside "BSD/Mac68k Booter" utility from
! FTP:3.7/mac68k/utils onto your hard disk. Configure the "BSD/Mac68k
Booter" with the location of your bsd.rd kernel and boot into the installer.
Refer to the instructions in INSTALL.mac68k for more details.
--- 544,550 ----
Boot MacOS as normal and extract the Macside "BSD/Mac68k Booter" utility from
! 3.7/mac68k/utils onto your hard disk. Configure the "BSD/Mac68k
Booter" with the location of your bsd.rd kernel and boot into the installer.
Refer to the instructions in INSTALL.mac68k for more details.
***************
*** 573,584 ****
Using the Linux built-in graphical ipkg installer, install the
openbsd37_arm.ipk package. Reboot, then run it. Read INSTALL.zaurus
for a few important details.
-
src.tar.gz contains a source archive starting at /usr/src. This file
contains everything you need except for the kernel sources, which are
--- 576,587 ----
Using the Linux built-in graphical ipkg installer, install the
openbsd37_arm.ipk package. Reboot, then run it. Read INSTALL.zaurus
for a few important details.
src.tar.gz contains a source archive starting at /usr/src. This file
contains everything you need except for the kernel sources, which are
***************
*** 608,616 ****
Using these files
results in a much faster initial CVS update than you could expect from
a fresh checkout of the full OpenBSD source tree.
-
How to install
-
!
!
+
OpenBSD/alpha:
OpenBSD/alpha:
OpenBSD/hp300:
--- 519,525 ----
OpenBSD/hp300:
***************
*** 541,547 ****
Notes about the source code:
+ Notes about the source code
! Note that most ports are available as packages through FTP. Updated packages for the 3.7 release will be made available if problems arise.
If you're interested in seeing a port added, would like to help out, or just ! would like to know more, the mailing list ports@openbsd.org is a good ! place to know.
! Note that most ports are available as packages on our mirrors. Updated packages for the 3.7 release will be made available if problems arise.
If you're interested in seeing a port added, would like to help out, or just ! would like to know more, the mailing list ! ports@openbsd.org is a good place to know.