--- 40,47 ----

See a detailed log of changes between the 5.7 and 5.8 releases.

signify(1) ! pubkeys for this release:

*************** *** 57,68 **** RWRlkI2aFHvL/XGqD+lFerD/xUi/jnAXKwdFQwZDekYwDrEPSpSWgpI9
!

All applicable copyrights and credits are in the src.tar.gz, sys.tar.gz, xenocara.tar.gz, ports.tar.gz files, or in the files fetched via ports.tar.gz. -

All applicable copyrights and credits are in the src.tar.gz, sys.tar.gz, xenocara.tar.gz, ports.tar.gz files, or in the files fetched via ports.tar.gz.

What's New

This is a partial list of new features and systems included in OpenBSD 5.8. For a comprehensive list, see the changelog leading --- 72,77 ---- *************** *** 600,606 ****

How to install

Following this are the instructions which you would have on a piece of paper if you had purchased a CDROM set instead of doing an alternate --- 598,603 ---- *************** *** 659,664 **** --- 656,663 ----

.../OpenBSD/5.8/zaurus/INSTALL.zaurus +

*************** *** 743,750 ****

OpenBSD/alpha:

! Write FTP:5.8/alpha/floppy58.fs or ! FTP:5.8/alpha/floppyB58.fs (depending on your machine) to a diskette and enter boot dva0. Refer to INSTALL.alpha for more details.

--- 742,749 ----

OpenBSD/alpha:

! Write 5.8/alpha/floppy58.fs or ! 5.8/alpha/floppyB58.fs (depending on your machine) to a diskette and enter boot dva0. Refer to INSTALL.alpha for more details.

*************** *** 819,830 ****

Boot from one of the provided install ISO images, using one of the two commands listed below, depending on the version of your ROM. !

  ok boot cdrom 5.8/sparc/bsd.rd
  or
  > b sd(0,6,0)5.8/sparc/bsd.rd
!

If your SPARC system does not have a CD drive, you can alternatively boot from floppy. --- 818,830 ----

Boot from one of the provided install ISO images, using one of the two commands listed below, depending on the version of your ROM. +

  ok boot cdrom 5.8/sparc/bsd.rd
  or
  > b sd(0,6,0)5.8/sparc/bsd.rd
!

If your SPARC system does not have a CD drive, you can alternatively boot from floppy. *************** *** 832,842 **** For more information see this page. To boot from the floppy use one of the two commands listed below, depending on the version of your ROM. ! !

  ok boot floppy
  or
! > b fd()

Make sure you use a properly formatted floppy with NO BAD BLOCKS or your install --- 832,843 ---- For more information see this page. To boot from the floppy use one of the two commands listed below, depending on the version of your ROM. !

  ok boot floppy
  or
! > b fd()
!

Make sure you use a properly formatted floppy with NO BAD BLOCKS or your install *************** *** 858,864 **** Using the Linux built-in graphical ipkg installer, install the openbsd58_arm.ipk package. Reboot, then run it. Read INSTALL.zaurus for a few important details. -

--- 859,864 ---- *************** *** 891,897 ****

  # mkdir -p /usr/src/sys
  # cd /usr/src
! # tar xvfz /tmp/sys.tar.gz

Both of these trees are a regular CVS checkout. Using these trees it --- 891,897 ----

  # mkdir -p /usr/src/sys
  # cd /usr/src
! # tar xvfz /tmp/sys.tar.gz

Both of these trees are a regular CVS checkout. Using these trees it *************** *** 901,907 **** results in a much faster initial CVS update than you could expect from a fresh checkout of the full OpenBSD source tree.

[Of course, you must replace the server name here with a nearby anoncvs --- 929,936 ---- the ports/ tree available on a read-write medium and update the tree with a command like: