===================================================================
RCS file: /cvsrepo/anoncvs/cvs/www/59.html,v
retrieving revision 1.64
retrieving revision 1.65
diff -u -r1.64 -r1.65
--- www/59.html 2016/03/08 21:24:59 1.64
+++ www/59.html 2016/03/09 05:49:21 1.65
@@ -957,145 +957,146 @@
Quick installer information for people familiar with OpenBSD, and the
use of the "disklabel -E" command. If you are at all confused when
installing OpenBSD, read the relevant INSTALL.* file as listed above!
-
OpenBSD/i386:
-
+
+
+
The OpenBSD/i386 release is on CD1.
Boot from the CD to begin the install - you may need to adjust
your BIOS options first.
-
+
If your machine can boot from USB, you can write install59.fs or
miniroot59.fs to a USB stick and boot from it.
-
+
If you can't boot from a CD, floppy disk, or USB,
you can install across the network using PXE as described in
the included INSTALL.i386 document.
-
+
If you are planning on dual booting OpenBSD with another OS, you will need to
read INSTALL.i386.
-
-
OpenBSD/amd64:
-
+
+
The OpenBSD/amd64 release is on CD2.
Boot from the CD to begin the install - you may need to adjust
your BIOS options first.
-
+
If your machine can boot from USB, you can write install59.fs or
miniroot59.fs to a USB stick and boot from it.
-
+
If you can't boot from a CD, floppy disk, or USB,
you can install across the network using PXE as described in the included
INSTALL.amd64 document.
-
+
If you are planning to dual boot OpenBSD with another OS, you will need to
read INSTALL.amd64.
-
OpenBSD/macppc:
-
+
+
+
Burn the image from a mirror site to a CDROM, and power on your machine
while holding down the C key until the display turns on and
shows OpenBSD/macppc boot.
-
+
Alternatively, at the Open Firmware prompt, enter boot cd:,ofwboot
/5.9/macppc/bsd.rd
-
OpenBSD/sparc64:
-
-Put CD3 in your CDROM drive and type boot cdrom.
+
+
+Put CD3 in your CDROM drive and type boot cdrom.
+
If this doesn't work, or if you don't have a CDROM drive, you can write
CD3:5.9/sparc64/floppy59.fs or CD3:5.9/sparc64/floppyB59.fs
(depending on your machine) to a floppy and boot it with boot
floppy. Refer to INSTALL.sparc64 for details.
-
+
Make sure you use a properly formatted floppy with NO BAD BLOCKS or your install
will most likely fail.
-
+
You can also write CD3:5.9/sparc64/miniroot59.fs to the swap partition on
the disk and boot with boot disk:b.
-
+
If nothing works, you can boot over the network as described in INSTALL.sparc64.
-
OpenBSD/alpha:
-
-
Write FTP:5.9/alpha/floppy59.fs or
+
+
+
+Write FTP:5.9/alpha/floppy59.fs or
FTP:5.9/alpha/floppyB59.fs (depending on your machine) to a diskette and
enter boot dva0. Refer to INSTALL.alpha for more details.
-
+
Make sure you use a properly formatted floppy with NO BAD BLOCKS or your install
will most likely fail.
-
-
OpenBSD/hppa:
-
-
+
+
+
Boot over the network by following the instructions in INSTALL.hppa or the
hppa platform page.
-
OpenBSD/landisk:
-
-
+
+
+
Write miniroot59.fs to the start of the CF
or disk, and boot normally.
-
OpenBSD/loongson:
-
-
+
+
+
Write miniroot59.fs to a USB stick and boot bsd.rd from it
or boot bsd.rd via tftp.
Refer to the instructions in INSTALL.loongson for more details.
-
-
OpenBSD/luna88k:
-
-
+
+
+
Copy `boot' and `bsd.rd' to a Mach or UniOS partition, and boot the bootloader
from the PROM, and then bsd.rd from the bootloader.
Refer to the instructions in INSTALL.luna88k for more details.
-
OpenBSD/octeon:
-
-
+
+
+
After connecting a serial port, boot bsd.rd over the network via DHCP/tftp.
Refer to the instructions in INSTALL.octeon for more details.
-
OpenBSD/sgi:
-
-
+
+
+
To install, burn cd59.iso on a CD-R, put it in the CD drive of your
machine and select Install System Software from the System Maintenance
menu. Indigo/Indy/Indigo2 (R4000) systems will not boot automatically from
@@ -1103,29 +1104,30 @@
Refer to the instructions in INSTALL.sgi for more details.
+
If your machine doesn't have a CD drive, you can setup a DHCP/tftp network
server, and boot using "bootp()/bsd.rd.IP##" using the kernel matching your
system type. Refer to the instructions in INSTALL.sgi for more details.
-
OpenBSD/socppc:
-
-
+
+
+
After connecting a serial port, boot over the network via DHCP/tftp.
Refer to the instructions in INSTALL.socppc for more details.
-
OpenBSD/vax:
-
+
+
Boot over the network via mopbooting as described in INSTALL.vax.
-
OpenBSD/zaurus:
-
-
+
+
+
Using the Linux built-in graphical ipkg installer, install the
openbsd59_arm.ipk package. Reboot, then run it. Read INSTALL.zaurus
for a few important details.
@@ -1133,9 +1135,9 @@
-
+
How to upgrade
-
+
If you already have an OpenBSD 5.8 system, and do not want to reinstall,
upgrade instructions and advice can be found in the
Upgrade Guide.