===================================================================
RCS file: /cvsrepo/anoncvs/cvs/www/70.html,v
retrieving revision 1.48
retrieving revision 1.49
diff -u -r1.48 -r1.49
--- www/70.html 2021/10/02 16:49:55 1.48
+++ www/70.html 2021/10/02 18:48:53 1.49
@@ -84,7 +84,7 @@
Support for the powerpc64 platform was improved:
- The arm64 platform support was improved with the following changes:
+ The arm64 platform support was improved with the following changes:
- Added aplpinctrl(4) driver for the Apple GPIO controller found on the M1 SoCs.
- Ensured rkpwm(4) can find the clock when using a recent device tree.
@@ -103,9 +103,9 @@
Changes on other architectures:
- - Switched macppc to use ld.lld(1).
+
- Switched macppc to use ld.lld(1).
- Fixed an issue preventing applications from selecting the non-ALTIVEC code path on macppc.
-
- Made amd64 hw.setperf percentages proportional to the enhanced
+
- Made amd64 hw.setperf percentages proportional to the enhanced
speed step frequencies on Intel processors. The default hw.setperf=99
corresponds to the maximum ordinary speed, and setting it to 100
enables turbo mode.
@@ -113,15 +113,15 @@
- Disabled base-gcc on amd64.
- Prevented crashes on amd64 when TLB entries which should have been invalidated were used.
- Prevented a kernel panic in sparc64 due to page boundary misalignment.
-
- Forced luna88k to use the serial console when no graphics board is found.
-
- Fixed strchr() and strrchr() on mips64.
+
- Forced luna88k to use the serial console when no graphics board is found.
+
- Made additional free inodes on luna88k bsd.rd by specifying density=4096.
+
- Fixed strchr() and strrchr() on mips64.
- Prevented watchdog resets on some i.MX 64-bit machines with a
recent U-Boot and watchdog enabled on boot in imxdog(8).
- Created audio devices on armv7.
-
- Made additional free inodes on luna88k bsd.rd by specifying density=4096.
-
- Retired OpenBSD/sgi platform.
-
- Enabled MSI-X support for powerpc64.
+
- Retired OpenBSD/sgi platform.
+
- Enabled MSI-X support for powerpc64.
- Fixed __ppc_lock for page faults that recursively grab the lock on powerpc.
- Increased the maximum data size on powerpc64 to 32GB.
@@ -595,21 +595,55 @@
href="https://man.openbsd.org/slaacd.8">slaacd(8).
Additionally these programms saw the following improvements and bugfixes:
- - Changed dhcpleased(8) client identifier transmission to match other dhcp client implementations.
-
- Simplified dhcpleasectl(8) and added syntax to match dhclient(8) (interface), allowing one to be aliased to the other.
-
- Retried broadcast with dhcpleased(8) when the dhcp server is unreachable via unicast UDP.
-
- Made resolvd(8) accept dns proposals for the loopback addresses.
-
- Added to dhcpleased.conf(5) the ability to ignore routes or nameservers from a lease and to ignore servers entirely.
+
- Changed dhcpleased(8) client
+ identifier transmission to match other dhcp client implementations.
+
- Simplified dhcpleasectl(8) and
+ added syntax to match dhclient(8) (interface),
+ allowing one to be aliased to the other.
+
- Retried broadcast with dhcpleased(8) when the
+ dhcp server is unreachable via unicast UDP.
+
- Made resolvd(8)
+ accept dns proposals for the loopback addresses.
+
- Added to dhcpleased.conf(5)
+ the ability to ignore routes or nameservers from a lease and to ignore
+ servers entirely.
- Left resolv.conf(5) to resolvd(8) rather than
recreating after finding nameservers.
-
- Made dhclient(8) defer to dhcpleased(8) when the inet autoconf flag is set. When run, dhclient will signal dhcpleased to request a new lease rather than requesting one itself.
-
- Fixed potential races in slaacd(8) and dhcpleased(8) when two processes are configuring the same IP.
-
- Added the possibility to send vendor class identifier and client identifier using dhcpleased.conf(5).
-
- Made dhcpleased(8) always configure provided routes, regardless of whether the address received in the lease is already configured.
-
- Used exclusive locks under /dev/ to ensure single instances of resolvd(8), slaacd(8) and dhcpleased(8).
-
- Implemented classless static routes dhcp option in dhcpleased(8).
-
- Added a new "nameserver" command to route(8), sending nameserver proposals to resolvd(8) using the dns proposal protocol over the route socket. This command is intended be used to integrate userland triggered nameserver changes, for example by VPN software.
+
- Made dhclient(8)
+ defer to dhcpleased(8) when the
+ inet autoconf flag is set. When run, dhclient will signal dhcpleased
+ to request a new lease rather than requesting one itself.
+
- Fixed potential races in slaacd(8) and dhcpleased(8) when two
+ processes are configuring the same IP.
+
- Added the possibility to send vendor class identifier and client
+ identifier using dhcpleased.conf(5).
+
- Made dhcpleased(8) always
+ configure provided routes, regardless of whether the address received
+ in the lease is already configured.
+
- Used exclusive locks under /dev/ to ensure single instances of resolvd(8), slaacd(8) and dhcpleased(8).
+
- Implemented classless static routes dhcp option in dhcpleased(8).
+
- Added a new "nameserver" command to route(8), sending
+ nameserver proposals to resolvd(8) using the dns
+ proposal protocol over the route socket. This command is intended be
+ used to integrate userland triggered nameserver changes, for example
+ by VPN software.
Changes to snmp related tools: