===================================================================
RCS file: /cvsrepo/anoncvs/cvs/www/70.html,v
retrieving revision 1.88
retrieving revision 1.89
diff -u -r1.88 -r1.89
--- www/70.html 2021/10/10 15:15:17 1.88
+++ www/70.html 2021/10/12 05:54:35 1.89
@@ -89,7 +89,7 @@
Added apldart(4) support for a DART with two sets of registers, needed to support the Synopsis DesignWare USB 3 controller.
Added apldwusb(4), a glue driver for the Synopsys DesignWare USB 3 controllers found on the Apple M1 SoC.
Added aplns(4) to provide support for Apple NVME storage as found in Apple M1 devices.
- Added aplpinctrl(4) driver for the Apple GPIO controller found on the M1 SoCs.
+ Added aplpinctrl(4), a driver for the Apple GPIO controller found on the M1 SoCs.
Added aplpmu(4), a driver for the Apple "sera" SPMI power management unit that contains the RTC on Apple M1 systems.
Added aplspmi(4), a driver for the Apple SPMI controller.
@@ -370,7 +370,7 @@
Added or improved wireless network drivers:
- - Zeroed out iwx(4) Tx descriptors of frames which are done to prevent the device from writing to the former DMA address of a buffer which has been taken off the Tx ring.
+
- Zeroed out iwx(4) Tx descriptors of frames which is done to prevent the device from writing to the former DMA address of a buffer which has been taken off the Tx ring.
- Fixed a bug in iwx(4) Tx done interrupt processing which could cause fatal firmware errors under load and memory corruption.
- Changed iwm(4) and iwx(4) to sleep for 1 second while loading firmware to match what iwn(4) does. This fixes some issues with suspend/resume.
- Ensured that iwm(4) and iwx(4) will reload firmware from disk on down/up and not during resume.
@@ -390,7 +390,7 @@
- Fixed node leaks in iwm(4) and iwx(4) which caused the drivers to get stuck when roaming between access points.
- Fixed iwx(4) firmware reloading after a failure to parse the firmware file.
- Avoided "mac clock not ready" panics in iwm(4) and iwx(4).
-
- Worked around a problem with certain athn(4) hardware that caused problem when running in HostAP mode with clients that use Tx aggregation.
+
- Worked around a problem between certain athn(4) hardware running in HostAP mode and clients that use Tx aggregation.
- Corrected multicast decryption for iwx(4).
- Added 802.11n Tx aggregation support to iwm(4).
- Made iwn(4), iwm(4) and iwx(4) keep track of beacon parameters at run-time.
@@ -479,15 +479,15 @@
- Fixed and use non-blocking connect for RTR sessions.
- Fully implemented RFC 6286 by checking for BGP ID collisions.
- Adjusted the 4-byte AS number handling to RFC 6793 by changing error
- behaviour from prefix witdraw to attribute discard.
+ behaviour from prefix withdraw to attribute discard.
- In bgpctl(8) print out both the sent "Neighbor capabilities" and the
"Negotiated capabilities" for a session.
- Print timestamps both as a formatted and a pure time in seconds
field in various JSON objects.
- Fixed a bug, where during bgpd(8) config reloads prefixes of the
wrong address family could leak to peers resulting in session resets.
-
- Added support for RFC 7313 - Enhanced Route Refresh
- Disabled by default, to enable use 'announce enhanced refresh yes'.
+
- Added support for RFC 7313 - Enhanced Route Refresh.
+ Disabled by default. To enable, use 'announce enhanced refresh yes'.
- Improved output of Adj-RIB-Out by updating nexthop and ASPATH before
adding the prefix to the RIB. This improves `bgpctl show rib out`
output.
@@ -537,7 +537,7 @@
- Reference-count and delete unused files synced via RRDP, as far as
possible.
- In the JSON output, changed the AS Number from a string ("AS123") to
- an integer ("123") to make processing of the output easier,
+ an integer ("123") to make processing of the output easier.
- Added an 'expires' column to CSV & JSON output, based on certificate
and CRL validity times. The 'expires' value can be used to avoid route
selection based on stale data when generating VRP sets, when faced
@@ -859,7 +859,7 @@
allowed signers files used by
ssh-keygen(1)
signatures now support listing key validity intervals
- alongside they key, and
+ alongside the keys, and
ssh-keygen(1)
can optionally check during signature verification whether a
specified time falls inside this interval. This feature is
@@ -955,7 +955,7 @@
unavailable in sftp-server read-only mode.
- ssh(1): fix SEGV
in UpdateHostkeys debug() message, triggered when the update
- removed more host keys than remain present.
+ removed more host keys than remained present.
- scp(1): when using
the SFTP protocol, continue transferring files after a
transfer error occurs, better matching original scp/rcp