===================================================================
RCS file: /cvsrepo/anoncvs/cvs/www/errata21.html,v
retrieving revision 1.81
retrieving revision 1.82
diff -u -r1.81 -r1.82
--- www/errata21.html	2019/05/27 22:55:19	1.81
+++ www/errata21.html	2019/05/28 16:32:41	1.82
@@ -84,8 +84,9 @@
 <hr>
 
 <ul>
+
 <li>
-<strong>CD RELEASE WORKAROUND</strong>
+<strong>001: CD RELEASE WORKAROUND</strong>
 &nbsp; <i>All architectures</i><br>
 One of the install scripts has a flaw that makes the CD-ROM mount fail
 when using the CD-ROM as the install source media.
@@ -105,15 +106,17 @@
 <pre><b>#</b> install
 </pre>
 <p>
+
 <li>
-<strong>CD RELEASE WORKAROUND</strong>
+<strong>002: CD RELEASE WORKAROUND</strong>
 &nbsp; <i>alpha only</i><br>
 CD2 does not boot on the alpha, as had been planned. Instead, you
 must use the floppy install method.  This is not significantly
 harder..
 <p>
+
 <li>
-<strong>BOOT BLOCK BUG</strong>
+<strong>003: BOOT BLOCK BUG</strong>
 &nbsp; <i>i386 only</i><br>
 Some rarer PC BIOSs do not like the hardrive bootblocks when used
 as a MBR.  The symptom is that the BIOS says "READ ERROR" when booting,
@@ -122,8 +125,9 @@
 MBR, then install OpenBSD in a partition all by itself starting at a
 non-zero offset.  For instance, start OpenBSD at next track boundary or so.
 <p>
+
 <li>
-<strong>WRONG CHECKSUMS</strong>
+<strong>004: WRONG CHECKSUMS</strong>
 &nbsp; <i>i386 only</i><br>
 The i386/X11/SUMS.md5 file contains 4 incorrect MD5 checksums.
 These have been corrected on the ftp mirrors. The correct lines are:<br>
@@ -136,8 +140,9 @@
 INSTALL.i386 document, and hence end up with geometry translation
 problems.  Read the document, please.
 <p>
+
 <li>
-<strong>RELEASE BUG</strong>
+<strong>005: RELEASE BUG</strong>
 &nbsp; <i>amiga only</i><br>
 The amiga install has a flaw wrt Tseng based graphic cards: when entering
 multiuser mode the console won't get a login prompt.  This is due to
@@ -147,8 +152,9 @@
 <b>#</b> sh MAKEDEV ttye6
 </pre>
 <p>
+
 <li>
-<strong>RELEASE BUG</strong>
+<strong>006: RELEASE BUG</strong>
 &nbsp; <i>sparc only</i><br>
 The sparc X11R6.3 xdm-config files reference /usr/X11R6.3/... This is
  to X11R6.3's default config file contents.  To fix, su and
@@ -158,15 +164,16 @@
 </pre>
 <p>
 <li>
-<strong>RELEASE BUG</strong>
+<strong>007: RELEASE BUG</strong>
 &nbsp; <i>sparc only</i><br>
 The sparc "single floppy install disk" has a problem when you specify
 "dumb" in response to the terminal type query.  As a work-around
 first specify an invalid terminal such as "bogus" and when prompted
 again for a terminal type, enter "dumb" and it will work correctly.
 <p>
+
 <li>
-<strong>RELEASE BUG</strong>
+<strong>008: RELEASE BUG</strong>
 &nbsp; <i>sparc only</i><br>
 When netbooting an older sparc system such as a Sun4 or Sun4c, the boot
 may hang up at the end of the tftp transfer of the bootstrap due
@@ -177,6 +184,7 @@
 <b>#</b> mv newboot boot
 </pre>
 <p>
+
 <li>
 <strong>RELEASE BUG</strong>
 &nbsp; <i>sparc only</i><br>
@@ -210,8 +218,9 @@
 <b>#</b>
 </pre>
 <p>
+
 <li>
-<strong>RELEASE BUG</strong>
+<strong>009: RELEASE BUG</strong>
 &nbsp; <i>pmax only</i><br>
 When using the X11R6 binaries from the 2.1 release you will get
 errors like:
@@ -234,8 +243,9 @@
 sensitive part of the system. You can remove the original_libc.so.16.1
 after the next reboot if everything is working fine.
 <p>
+
 <li>
-<strong>RELEASE BUG</strong>
+<strong>010: RELEASE BUG</strong>
 &nbsp; <i>mac68k only</i><br>
 The installer generates incorrect /etc/fstab files causing messages such
 as "file system read-only" on bootup.  To correct, boot to single-user
@@ -256,8 +266,9 @@
 The installer should not have specified the filesystem as the old
 "ufs" type; the "ffs" type is more correct.
 <p>
+
 <li>
-<strong>RELEASE BUG</strong>
+<strong>011: RELEASE BUG</strong>
 &nbsp; <i>mac68k only</i><br>
 The installer forgets to install the kernel onto the filesystem.
 This is because the installer expects all packages including the kernel to