===================================================================
RCS file: /cvsrepo/anoncvs/cvs/www/hppa.html,v
retrieving revision 1.95
retrieving revision 1.96
diff -c -r1.95 -r1.96
*** www/hppa.html 2003/03/03 16:07:27 1.95
--- www/hppa.html 2003/03/04 18:50:02 1.96
***************
*** 99,111 ****
- Improve overall stability
!
- Support the NCR53C700 SCSI controller
!
- Support the NCR53C720 SCSI controller
- Installation procedures
- Improve port-specific documentation
!
- Support booting from tape and cdrom
!
- Support for 7300LC and 8x00 cpus
!
- Support for 7000 cpus (the "original snakes" machines)
- HP-UX emulation
- PARISC/Linux emulation
- Shared libraries
--- 99,111 ----
- Improve overall stability
!
- Support the NCR53C700 SCSI Narrow SE controller
!
- Support the NCR53C720 SCSI FWD controller
- Installation procedures
- Improve port-specific documentation
!
- Support booting from tape and CD-ROM
!
- Support for 7300LC and 8x00 CPUs
!
- Support for 7000 CPUs (the "original snakes" machines)
- HP-UX emulation
- PARISC/Linux emulation
- Shared libraries
***************
*** 174,180 ****
- SCSI controllers
! - NCR53C710 SCSI I/O Processors
(osiop)
- Ethernet
--- 174,180 ----
SCSI controllers
! - NCR53C710 SCSI Narrow SE controller
(osiop)
Ethernet
***************
*** 213,237 ****
The following systems may eventually work:
- PA7000-based machines: 705, 710, 720, 730, 750
- PA2.0 systems (in 32-bit mode)
- HP 9000 836, 844, 845, 846
!
- HP 9000 E23, E25, E35, E45, E55
!
- HP 3000 908, 918, 928, 938
- Hitachi VQ200, VQ210, and some other non-HP workstations
!
- Hitachi 9000V 3050RX/200, 3050RX/10C and 3500/*
- Precision Book from RDI Computer Corporation (well, unlikely)
- HP VME and VXI single board systems (requires VME at least)
These systems will, probably, never be supported by this port since
they are of 1.0 PA-RISC architecture, which is substantially
! inferiour to the 1.1:
- HP 9000 600, 635, 645
- HP 9000 800, 808, 815, 822, 825, 832, 834, 835, 840, 842, 845, 850, 852, 855, 860, 865, 870, 890
-
- HP 9000 900
--- 213,247 ----
The following systems may eventually work:
- PA7000-based machines: 705, 710, 720, 730, 750
+
- PA7300LC-based machines: A180[C], B132L[+], B160L, B180L, C132L, C160L
- PA2.0 systems (in 32-bit mode)
- HP 9000 836, 844, 845, 846
!
- HP 9000 E-Class (with limited I/O)
!
- HP 9000 D-Class, at least the 32-bit models
- Hitachi VQ200, VQ210, and some other non-HP workstations
!
- Hitachi 9000V 3050RX/200, 3050RX/100C and 3500/*
- Precision Book from RDI Computer Corporation (well, unlikely)
- HP VME and VXI single board systems (requires VME at least)
+ The following systems are very unlikely to be supported since they either have
+ incompatible firmware (the 3000s) or have almost completely undocumented I/O
+ subsystems:
+
+ - HP 3000 900
+
- HP 9000 8x7 (F, G, H, I-Class)
+
+
+
+
These systems will, probably, never be supported by this port since
they are of 1.0 PA-RISC architecture, which is substantially
! inferior to the 1.1:
- HP 9000 600, 635, 645
- HP 9000 800, 808, 815, 822, 825, 832, 834, 835, 840, 842, 845, 850, 852, 855, 860, 865, 870, 890
***************
*** 456,461 ****
www@openbsd.org
! $OpenBSD: hppa.html,v 1.95 2003/03/03 16:07:27 mickey Exp $