-Note: Problems for which patches exist are marked in red.
+Note: Problems for which patches exist are marked in red.
For changes in other releases, click below:
@@ -82,1258 +88,1254 @@
-
Changes made between OpenBSD 5.2 and 5.3
+
Changes made between OpenBSD 5.2 and 5.3
-
dhclient(8) now tries 10 times to obtain the routing table via sysctl(3), if it can't be done abandons attempt to clean up the routing and arp(4) tables and carries on.
+
dhclient(8) now tries 10 times to obtain the routing table via sysctl(3), if it can't be done abandons attempt to clean up the routing and arp(4) tables and carries on.
-
Fixed xterm(1) segfault which happened when using the mouse wheel over the scrollbar.
-
Avoid alignment errors when dhclient(8) processing routing messages, by reading the messages into dynamically allocated memory.
-
Added ldomctl(8/sparc64) workaround for some firmware revisions which provided an incorrect factory-default configuration.
-
Fixed sndiod(8) crashes occurring when the client sample frequency is much larger than the device sample frequency.
-
Don't try to purge one-time rules from the main pf.conf(5) ruleset.
+
Fixed xterm(1) segfault which happened when using the mouse wheel over the scrollbar.
+
Avoid alignment errors when dhclient(8) processing routing messages, by reading the messages into dynamically allocated memory.
+
Added ldomctl(8/sparc64) workaround for some firmware revisions which provided an incorrect factory-default configuration.
+
Fixed sndiod(8) crashes occurring when the client sample frequency is much larger than the device sample frequency.
+
Don't try to purge one-time rules from the main pf.conf(5) ruleset.
-
Always reserve space addresses, to fix memory corruption when doing ipsecctl(8) -ssa with md5sig.
-
Fixed trunk(4) panic which occurred when previous interface had modified the mbuf(9) chain.
+
Always reserve space addresses, to fix memory corruption when doing ipsecctl(8) -ssa with md5sig.
+
Fixed trunk(4) panic which occurred when previous interface had modified the mbuf(9) chain.
-
Use dma memory for viomb(4) bl_pages, to fix a "Non dma-reachable buffer..." panic on amd64.
+
Use dma memory for viomb(4) bl_pages, to fix a "Non dma-reachable buffer..." panic on amd64.
-
When no acceptable dhclient(8) offers are received within the allowed timeframe, look for a lease in dhclient.leases.IF. If none are available, wait "retry" seconds before restarting DISCOVER; also daemonise the process, giving back the command prompt.
+
When no acceptable dhclient(8) offers are received within the allowed timeframe, look for a lease in dhclient.leases.IF. If none are available, wait "retry" seconds before restarting DISCOVER; also daemonise the process, giving back the command prompt.
-
Support ssh(1) ProxyCommand=- (stdin/out already point to the proxy); Allow IdentityFile=none.
+
Support ssh(1) ProxyCommand=- (stdin/out already point to the proxy); Allow IdentityFile=none.
-
Don't complain if ssh(1) IdentityFiles specified in system-wide configs are missing.
-
Bring back bge(4) 5718/5719/5720 support again; fixes for ip checksum handling.
-
Fixed a potential smtpd(8) crash when connecting to a misbehaving smtp server.
-
Use imsg_flush() to ensure a quicker exit of any previous copy of dhclient(8).
+
Don't complain if ssh(1) IdentityFiles specified in system-wide configs are missing.
+
Bring back bge(4) 5718/5719/5720 support again; fixes for ip checksum handling.
+
Fixed a potential smtpd(8) crash when connecting to a misbehaving smtp server.
+
Use imsg_flush() to ensure a quicker exit of any previous copy of dhclient(8).
-
Cancel any outstanding protocol timeouts when a dhclient(8) link goes away.
+
Cancel any outstanding protocol timeouts when a dhclient(8) link goes away.
Reverted revision 1.195 of ahci_pci.c, which caused Intel SATA controllers in compat mode to not see any hard disks on boot.
-
When opening an ldomd(8/sparc64) device node fails, show its path in the error message.
+
When opening an ldomd(8/sparc64) device node fails, show its path in the error message.
-
Set wireless interface priority and interfaces to the wlan group for cnw(4) and ray(4) (pre 802.11b wireless drivers).
-
install(1) will now report unlink() errors unless ENOENT.
-
Unbreak dhclient(8) DISCOVER, by initialising xid from correct field.
-
Allocate dma memory below 2^28 limit, allowing ice1712-based envy(4) cards to work on amd64.
-
Fixed the relayd(8) "toread" check in the lateconnect case, which allows Content-Length: 0 in HTTP GET request when a request filter is used. Broken by previous commit.
-
Do not loop forever if pckbc(4) keyboard send a BAT (Basic Assurance Test) fault code. Handle this code like "Resend" or "BAT success" instead.
+
Revert rthread/ld.so(1) diff: not working on sparc/sparc64 or vax.
+
Fixed make(1) var module failing while expanding a line ending with a $. Seen when MALLOC_OPTIONS=S.
+
Unbreak dhclient(8) DISCOVER, by initialising xid from correct field.
+
Allocate dma memory below 2^28 limit, allowing ice1712-based envy(4) cards to work on amd64.
+
Fixed the relayd(8) "toread" check in the lateconnect case, which allows Content-Length: 0 in HTTP GET request when a request filter is used. Broken by previous commit.
+
Do not loop forever if pckbc(4) keyboard send a BAT (Basic Assurance Test) fault code. Handle this code like "Resend" or "BAT success" instead.
-
Make sure dhclient(8) asks for a default route in the correct routing domain. Fixes some periodic failures.
-
Don't leak dhclient(8) routing socket file descriptor if getting the default route fails.
-
Warn more loudly if an ssh(1) IdentityFile provided by the user cannot be read (bz #1981).
-
Disable nginx(8) pcre symbol visibility on vax in order to unbreak the build.
+
Make sure dhclient(8) asks for a default route in the correct routing domain. Fixes some periodic failures.
+
Don't leak dhclient(8) routing socket file descriptor if getting the default route fails.
+
Warn more loudly if an ssh(1) IdentityFile provided by the user cannot be read (bz #1981).
+
Disable nginx(8) pcre symbol visibility on vax in order to unbreak the build.
When an interface generates an RTM_IFINFO message, check LLADDR. If it has changed, simulate a SIGHUP to restart.
-
Obey RFC 2131: when the broadcast flag is set, send dhcpd(8) reply back via udp broadcast and link-local broadcast. Fixes some switches which use the broadcast flag.
-
Correct ssh(1) error message that had a typo and was logging the wrong thing.
-
Don't rely on the dhclient(8) packet buffer (client->packet) being preserved between attempts to send DISCOVER or REQUEST packets.
+
Obey RFC 2131: when the broadcast flag is set, send dhcpd(8) reply back via udp broadcast and link-local broadcast. Fixes some switches which use the broadcast flag.
+
Correct ssh(1) error message that had a typo and was logging the wrong thing.
+
Don't rely on the dhclient(8) packet buffer (client->packet) being preserved between attempts to send DISCOVER or REQUEST packets.
Repair the legacy xf86-video-intel i810 driver.
-
Cherry pick bugfixes for http://www.openssl.org/news/secadv_20130205.txt from the openssl(1) repository.
-
Allow use of "=" instead of "=>" when declaring a smtpd.conf(5) mapping.
-
Replaced smtpd.conf(5) "users" keyword with "userbase" when providing alternate userbase.
-
smtpctl(8) trace expand, enables tracing of aliases expansion.
+
Cherry pick bugfixes for http://www.openssl.org/news/secadv_20130205.txt from the openssl(1) repository.
+
Allow use of "=" instead of "=>" when declaring a smtpd.conf(5) mapping.
+
Replaced smtpd.conf(5) "users" keyword with "userbase" when providing alternate userbase.
+
smtpctl(8) trace expand, enables tracing of aliases expansion.
-
Install 50x.html for nginx(8), which is part of a default configuration.
-
Disable ld(1) "PIE-by-default" if -static (or an alias) is passed on the command line, to produce a fully static binary.
-
netstat(1) -vP now also shows the new struct sockbuf field sb_flagsintr.
-
Make pflow(4) use flowStartSeconds/flowEndSeconds for netflow v10, so it can see what time a flow started/ended.
-
smtpd(8) fixes: handle getaddrinfo() error as LKA_TEMPFAIL; handle getsockname() error in smtp_connected(); accept "/" as part of user-part and expand to ":" (like qmail); fix wrong check in mda leading to bogus Return-Path header; fix aliases parsing when there's a white space between key and separator.
-
Automatically reflow wrapped lines when a tmux(1) pane is resized.
-
Don't let tmux(1) set certain string formats if the string is NULL.
+
sshd_config(5) MaxStartups is now "10:30:100" to start random early drops at 10 to 100 connections. Makes it harder to DoS.
+
Rework http content/chunk handling in relayd(8). Allows handling an optional chunk trailer properly (a prerequisite for splicing persistent http connections).
+
Install 50x.html for nginx(8), which is part of a default configuration.
+
Disable ld(1) "PIE-by-default" if -static (or an alias) is passed on the command line, to produce a fully static binary.
+
netstat(1) -vP now also shows the new struct sockbuf field sb_flagsintr.
+
Make pflow(4) use flowStartSeconds/flowEndSeconds for netflow v10, so it can see what time a flow started/ended.
+
smtpd(8) fixes: handle getaddrinfo() error as LKA_TEMPFAIL; handle getsockname() error in smtp_connected(); accept "/" as part of user-part and expand to ":" (like qmail); fix wrong check in mda leading to bogus Return-Path header; fix aliases parsing when there's a white space between key and separator.
+
Automatically reflow wrapped lines when a tmux(1) pane is resized.
+
Don't let tmux(1) set certain string formats if the string is NULL.
-
Make sure new config file is valid before SIGHUP'ing sshd(8), which would otherwise just kill it.
-
Pad "join BSS" command with padding the size of the entire buffer, to make rsu(4) firmware happy.
+
Make sure new config file is valid before SIGHUP'ing sshd(8), which would otherwise just kill it.
+
Pad "join BSS" command with padding the size of the entire buffer, to make rsu(4) firmware happy.
-
Stop as(1) from optimising away R_X86_64_GOTPCREL relocations.
-
Use RTM_GET in dhclient(8) to obtain the current default route. Much less work for the routing system.
+
Stop as(1) from optimising away R_X86_64_GOTPCREL relocations.
+
Use RTM_GET in dhclient(8) to obtain the current default route. Much less work for the routing system.
-
Removed product/vendor table and let the urndis(4) driver attach based on class, etc. Print what type of device it is.
-
Write out resolv.conf(5) only if the default route is under the control of the process binding the dhclient(8) lease. Re-check the default route when a routing message arrives that might mean default route has changed, and write out resolv.conf(5) if appropriate. Reduces the chances that the name servers in resolv.conf(5) are unreachable.
-
Don't tweak the smtpd(8) socket sndbuf, now that envelopes are passed in compressed form. Reduces default envelope message size.
-
Fixed port numbers for login_radius(8) servers, which were not configured correctly in npppd(8).
+
Rewritten the msk(4) receive filter handling code and cleaned up ioctl.
+
Write out resolv.conf(5) only if the default route is under the control of the process binding the dhclient(8) lease. Re-check the default route when a routing message arrives that might mean default route has changed, and write out resolv.conf(5) if appropriate. Reduces the chances that the name servers in resolv.conf(5) are unreachable.
+
Don't tweak the smtpd(8) socket sndbuf, now that envelopes are passed in compressed form. Reduces default envelope message size.
+
Fixed port numbers for login_radius(8) servers, which were not configured correctly in npppd(8).
-
Deleting the ip address of a tun(4) interface by npppd(8) now works correctly.
-
Backed out bge(4) 5718/5719/5720 support, as it breaks 5704C.
+
Deleting the ip address of a tun(4) interface by npppd(8) now works correctly.
+
Backed out bge(4) 5718/5719/5720 support, as it breaks 5704C.
-
Rewritten the url(4) receive filter handling code and cleaned up the ioctl bits.
-
Fixed udav(4) bug: when going in and out of promiscuous mode the driver was not disabling all multicast mode.
-
bge(4) support for 5718 family of chips, including the 5719 and 5720.
-
Make ulpt(4) upload firmware into HP LaserJet printers which require the firmware.
-
Large reduction in memory footprint when smtpd(8) is relaying lots of messages.
-
Log sender address as "<>" when smtpd(8) delivering bounces.
-
Allow lookups from backends in smtpd(8) "accept for [...] virtual" context.
-
Openldap client now accepts connections to a ssl-enabled ldapd(8) server.
-
Introduced smtpctl(8) "trace lookup" to trace lookup process; improved logging of the transfer process.
+
Fixed udav(4) bug: when going in and out of promiscuous mode the driver was not disabling all multicast mode.
+
bge(4) support for 5718 family of chips, including the 5719 and 5720.
+
Make ulpt(4) upload firmware into HP LaserJet printers which require the firmware.
+
Large reduction in memory footprint when smtpd(8) is relaying lots of messages.
+
Log sender address as "<>" when smtpd(8) delivering bounces.
+
Allow lookups from backends in smtpd(8) "accept for [...] virtual" context.
+
Openldap client now accepts connections to a ssl-enabled ldapd(8) server.
+
Introduced smtpctl(8) "trace lookup" to trace lookup process; improved logging of the transfer process.
-
Added TX interrupt mitigation for vr(4) chips, including 6105Ms found in pcengines alix and soekris 5501s.
+
Added TX interrupt mitigation for vr(4) chips, including 6105Ms found in pcengines alix and soekris 5501s.
Bumped MAXTSIZ to 128 MB in vmparam.h on i386 and amd64, to cope with large binaries.
-
Added a pkg_mklocatedb(1) -u option to make it possible to update an existing database.
+
Added a pkg_mklocatedb(1) -u option to make it possible to update an existing database.
-
Correct the PBA size used for em(4) PCH adapters to 26KB.
-
Calculate resolv.conf(5) contents once when dhclient(8) is binding a lease, and reuse as required.
-
Restore dhclient(8) "no domain-name, no domain-name-servers means don't touch resolv.conf" behaviour.
-
smtpd(8) updates: preliminary ldap and sqlite support; all lookups now done through tables; improved handling of temporary errors; improved scheduler and mta logic; improved queue; improved memory usage under high load; SSL certs/keys isolated to lookup process to avoid facing network; fully virtual setups possible now; and runtime tracing of processes through smtpctl(8) trace; smtpd.conf(5) simplified. FLUSH YOUR QUEUE.
-
Don't allow stopping/restarting mountd(8) via rc.d(8) framework, it should be done manually to avoid RPC daemon issues.
+
Correct the PBA size used for em(4) PCH adapters to 26KB.
+
Calculate resolv.conf(5) contents once when dhclient(8) is binding a lease, and reuse as required.
+
Restore dhclient(8) "no domain-name, no domain-name-servers means don't touch resolv.conf" behaviour.
+
smtpd(8) updates: preliminary ldap and sqlite support; all lookups now done through tables; improved handling of temporary errors; improved scheduler and mta logic; improved queue; improved memory usage under high load; SSL certs/keys isolated to lookup process to avoid facing network; fully virtual setups possible now; and runtime tracing of processes through smtpctl(8) trace; smtpd.conf(5) simplified. FLUSH YOUR QUEUE.
+
Don't allow stopping/restarting mountd(8) via rc.d(8) framework, it should be done manually to avoid RPC daemon issues.
-
Skip ssh(1) serial lookup when certificate's serial number is zero.
-
Changed byte-order swapping to 16 bits to match "event type" size. mpii(4) works on sparc64 with this.
-
Try to post everything except the flags field in the first myx(4) TX descriptor.
-
Fixed ssh(1) handling of (unused) KRL signatures; skip string in correct buffer.
-
Always validate the user of a received SNMPv3 request in snmpd(8) if the configured user has a certain security level.
+
Changed byte-order swapping to 16 bits to match "event type" size. mpii(4) works on sparc64 with this.
+
Try to post everything except the flags field in the first myx(4) TX descriptor.
+
Fixed ssh(1) handling of (unused) KRL signatures; skip string in correct buffer.
+
Always validate the user of a received SNMPv3 request in snmpd(8) if the configured user has a certain security level.
ARMv7 doesn't support the atomic SWP instruction anymore so using the atomic load and store instructions instead.
Added instruction fault register functions, which will be needed for further ARMv7 support.
-
m88k ld.so(1) now copes if shared library is loaded at a different address than what it was compiled for. Fixes spurious crashes.
-
Change interface and span interface lists so bridge(4) behaviour does not suddenly change anymore when adding a vlan(4) interface.
+
m88k ld.so(1) now copes if shared library is loaded at a different address than what it was compiled for. Fixes spurious crashes.
+
Change interface and span interface lists so bridge(4) behaviour does not suddenly change anymore when adding a vlan(4) interface.
-
relayd(8) now only sends a single CRLF terminator between Chunked Transfer Encoding chunks. Fixes (e.g.) Chrome and curl that implement the specification strictly.
+
relayd(8) now only sends a single CRLF terminator between Chunked Transfer Encoding chunks. Fixes (e.g.) Chrome and curl that implement the specification strictly.
-
Make pf(4) TCP sequence number tracking less strict by one octet for FIN packets. Previously a packet with the FIN bit set and containing data that fits exactly into the announced window was blocked.
-
Properly handle wcsftime(3) "%%" and "%N" where N is not a supported escape. Consistent with strftime(3) behaviour.
-
Stopped the radeon(4) driver from trying to restore text mode on PALM and newer chip generations, as it won't succeed.
-
Fixed backslash escaping during filename tab-completion in ksh(1).
-
Make pf(4) TCP sequence number tracking less strict by one octet for FIN packets. Previously a packet with the FIN bit set and containing data that fits exactly into the announced window was blocked.
+
Properly handle wcsftime(3) "%%" and "%N" where N is not a supported escape. Consistent with strftime(3) behaviour.
+
Stopped the radeon(4) driver from trying to restore text mode on PALM and newer chip generations, as it won't succeed.
+
Fixed backslash escaping during filename tab-completion in ksh(1).
+
Do not allow tmux(1) cursor colours to be set beginning with ? as that will report the colour.
Allow the kernel to directly transfer UDP data from one socket to another.
-
Allow two minutes until ospfd(8) neighbour adjacencies are formed; transmit correct state to RDE; do not send IMSG_LS_UPD if we have no links; and improved snapshot handling.
-
For ospfd(8) point-to-point interfaces, send lsupdates to the interface address (see RFC 2328, 13.3(5)).
-
In ospfd(8), check for state != NBR_STA_XCHNG even if the RDE has processed all received DDs (dd_pending == 0), in case the peer still sends more DD messages.
+
Allow two minutes until ospfd(8) neighbour adjacencies are formed; transmit correct state to RDE; do not send IMSG_LS_UPD if we have no links; and improved snapshot handling.
+
For ospfd(8) point-to-point interfaces, send lsupdates to the interface address (see RFC 2328, 13.3(5)).
+
In ospfd(8), check for state != NBR_STA_XCHNG even if the RDE has processed all received DDs (dd_pending == 0), in case the peer still sends more DD messages.
Imported xf86-video-modesetting 0.6.0 for KMS testing.
-
Display some more flags and subtypes in tcpdump(8), especially flags used in power saving mode.
-
Converted softraid(4) concat and RAID 0 to the new ccb functions.
-
Fixup printing of bgpd(8) rdomain configs to add network statements and only print the description if it is set.
+
Display some more flags and subtypes in tcpdump(8), especially flags used in power saving mode.
+
Converted softraid(4) concat and RAID 0 to the new ccb functions.
+
Fixup printing of bgpd(8) rdomain configs to add network statements and only print the description if it is set.
Allow amd64 to hibernate with up to 64GB physical memory.
-
Force three newest generations of Intel SATA chipsets into ahci(4) mode. Makes the DVD drive and other devices on MacBook Pro with bootcamp more reliable.
-
Fixed a.out(5) coredumps by using RB_FOREACH_SAFE in uvm(9).
+
Force three newest generations of Intel SATA chipsets into ahci(4) mode. Makes the DVD drive and other devices on MacBook Pro with bootcamp more reliable.
+
Fixed a.out(5) coredumps by using RB_FOREACH_SAFE in uvm(9).
Revert unconditionally registering the cpu throttling code on all loongson 2F systems, as the gdium does not have a separate scheduling clock yet.
Do not register the mips64 internal cpu timer-based timecounter if we support cpu throttling.
-
Properly distinguish /boot(8) and biosboot(8) in i386 and amd64 informational and error messages.
-
Unbreak the negation toggle code when re-loading pf(4) tables, so negating existing entries on re-load will work.
-
Add terminfo(5) entries for rxvt-unicode and rxvt-unicode-256color.
+
Properly distinguish /boot(8) and biosboot(8) in i386 and amd64 informational and error messages.
+
Unbreak the negation toggle code when re-loading pf(4) tables, so negating existing entries on re-load will work.
+
Add terminfo(5) entries for rxvt-unicode and rxvt-unicode-256color.
Added cpu throttling support to the loongson 2F systems.
-
Added a new capability flag to identify softraid(4) disciplines where read failures are not necessarily terminal (i.e. we have redundancy).
+
Added a new capability flag to identify softraid(4) disciplines where read failures are not necessarily terminal (i.e. we have redundancy).
-
Don't tell the dhclient(8) privileged process to discard active_addr if there is a pending address addition. Fixes "routehandler: interface address added" messages and premature exiting.
-
Added hardware VLAN tag/untag support for vr(4) VT6105M chips.
-
Keep a count of packets added to vr(4) TX queue and only poke the chip if we've added a packet.
+
Don't tell the dhclient(8) privileged process to discard active_addr if there is a pending address addition. Fixes "routehandler: interface address added" messages and premature exiting.
+
Added hardware VLAN tag/untag support for vr(4) VT6105M chips.
+
Keep a count of packets added to vr(4) TX queue and only poke the chip if we've added a packet.
Added a stat clock for the lemote loongson machines, to show more accurate cpu usage statistics.
-
Restrict sysctl(8) KERN_PROC_ARGS lookup of KERN_PROC_NENV and KERN_PROC_ENV to process owner and root.
-
On loongson, added a driver for the mfgpt1 clock found on lemote and use as system clock; replaced system clock provided by the cpu with a mfgpt to allow cpu throttling; changed the frequency value of hz from 100 to 128.
-
Track, reject and blackhole ospf6d(8) routes and allow them to be redistributed even though they point to the loopback.
Free the directory block buffer at the completion of a readdir, significantly reducing NTFS kernel memory usage.
-
When posting descriptors to the myx(4) chips rings, do multiple writes before calling the bus_space barrier.
-
Let dhclient(8)'s lease validate option data and discard bad options before checking if any required options are missing.
-
More informative dhclient(8) "options" error message.
-
Ignore dhclient(8) options that do not validate, rather than summarily rejecting offered lease. Treat all options whose names start with "option-" as unknown.
-
Reverted cwm(1) group.c r1.68, which allows an empty group to be sticky.
+
When posting descriptors to the myx(4) chips rings, do multiple writes before calling the bus_space barrier.
+
Let dhclient(8)'s lease validate option data and discard bad options before checking if any required options are missing.
+
More informative dhclient(8) "options" error message.
+
Ignore dhclient(8) options that do not validate, rather than summarily rejecting offered lease. Treat all options whose names start with "option-" as unknown.
+
Reverted cwm(1) group.c r1.68, which allows an empty group to be sticky.
-
Enabled flow control support with bnx(4) 5708S/5709S adapters.
-
Added support for reporting flow control status for mii(4) 5708S/5709S fibre phy.
-
Don't propagate XF86XK_Audio{Lower,Raise}Volume keys from pckbd(4) or wscons(4) to userspace. Stops volume from being adjusted twice (by X apps and again by the kernel).
-
Make dhclient(8) buffer for lease longer to accomodate strings listing all possible option names.
-
Don't propagate XF86XK_Audio{Lower,Raise}Volume keys from pckbd(4) or wscons(4) to userspace. Stops volume from being adjusted twice (by X apps and again by the kernel).
+
Make dhclient(8) buffer for lease longer to accomodate strings listing all possible option names.
+
Updated libXcomposite to 0.4.4; libXdamage to 1.4.4; and xf86-video-mach64 to 6.9.4.
-
Check UDP length field for short as well as long values in dhcpd(8) and dhclient(8). Fixes dhcpd(8) crash when a UDP packet arrives saying it has 0 length.
+
Check UDP length field for short as well as long values in dhcpd(8) and dhclient(8). Fixes dhcpd(8) crash when a UDP packet arrives saying it has 0 length.
Switched m88k ports to ELF.
-
Stopped rtsx(4) and sdhc(4) drivers attaching to the same device, which then failed to work reliably.
-
Allow for the units(1) prefix to be given without a need to quote it.
-
Make the per-user login_yubikey(8) counter file r/w by group auth.
+
Make the per-user login_yubikey(8) counter file r/w by group auth.
Added support for U3 bridges present in macppc G5 machines.
Attach all known macppc U3 AGP bridges.
-
acx(4) now supports power-saving in hostap mode.
-
Return EEXIST to "add" and "addspan" when a port is already a bridge(4) member. Makes reconfiguration with netstart(8) silent again.
-
Fixed bug in random offset from rev 1.143 of malloc(3); random range was expanded, but not by enough.
+
acx(4) now supports power-saving in hostap mode.
+
Return EEXIST to "add" and "addspan" when a port is already a bridge(4) member. Makes reconfiguration with netstart(8) silent again.
+
Fixed bug in random offset from rev 1.143 of malloc(3); random range was expanded, but not by enough.
-
When dhclient(8) is binding to a new lease, wait for the RTM_NEWADDR message in S_BOUND state. Prevents confusion when another DHCPACK arrives.
-
Fixed sasyncd(8): the valid port interval is 1 to 65535, not 1 to 65534.
-
Rather than calling microtime in bpf(4) bpf_catchpacket each time it's called on a packet, take a timeval indicating when the packet was captured.
-
bpf(4) allocates packet buffers in the ioctl path; let it sleep waiting for memory to become available.
+
When dhclient(8) is binding to a new lease, wait for the RTM_NEWADDR message in S_BOUND state. Prevents confusion when another DHCPACK arrives.
+
Fixed sasyncd(8): the valid port interval is 1 to 65535, not 1 to 65534.
+
Rather than calling microtime in bpf(4) bpf_catchpacket each time it's called on a packet, take a timeval indicating when the packet was captured.
+
bpf(4) allocates packet buffers in the ioctl path; let it sleep waiting for memory to become available.
-
Use openpty() rather than hand-rolled vi(1) pty opening code.
-
Correctly update the current ix(4) flow control mode; report it in the media status callback.
-
max_frame_size now set after ether_ifattach updates ix(4) if_mtu.
-
Readjust sndiod(8) midi flow control after consuming input data.
-
Added gcc(1) stack smashing protector for Alpha and MIPS (enabled by default). Reorganised soft frame pointer so that locals are below it and grow downwards.
+
Use openpty() rather than hand-rolled vi(1) pty opening code.
+
Correctly update the current ix(4) flow control mode; report it in the media status callback.
+
max_frame_size now set after ether_ifattach updates ix(4) if_mtu.
+
Readjust sndiod(8) midi flow control after consuming input data.
+
Added gcc(1) stack smashing protector for Alpha and MIPS (enabled by default). Reorganised soft frame pointer so that locals are below it and grow downwards.
Update to xf86-video-vmware 2.1 RC1 (aka 2.0.99.901).
Removed an output probe method in xf86-video-intel i830PreInit(). With xserver 1.13 this causes a fatal error at run time.
Sync the "legacy" xf86-video-intel i810 driver (used only on true i810 and i815 chipsets) to X.Org.
-
Temporarily bring back the scsi(8) shutdown hook, but only use it to flush the disk cache.
-
If no domain-name or domain-name-servers provided in the dhclient(8) lease (or if they are ignore'd in dhclient.conf(5)) and there is no resolv.conf.tail, then do not remove any existing resolv.conf(5).
+
If no domain-name or domain-name-servers provided in the dhclient(8) lease (or if they are ignore'd in dhclient.conf(5)) and there is no resolv.conf.tail, then do not remove any existing resolv.conf(5).
Attach the 2nd core of SPARC64-VI and SPARC64-VII CPUs.
-
Stopped cu(1) sending EOF "character" down serial line at high speed if it loses its input terminal.
-
Added ifconfig(8) group support back (ramdisk version was broken).
-
Close sparc64 vdsp disk images if the client disconnects.
New CA root certificates from GlobalSign, VeriSign, AddTrust, Comodo, UserTrust Network/UTN and Starfield.
Fix XAA support in xf86-video-mga.
-
For netstart(8), use the compact version of the check for ifconfig(8)'able interfaces from install.sub.
-
Added sshd_config(5) AllowTcpForwarding "local" and "remote" keywords to enable just local or remote TCP forwarding.
-
ssh-add(1) -d will now delete the corresponding certificate too; the -k option will delete key only.
-
Fixed sshd(8) logging of authentication when privsep is enabled by adding explicit "Partial" state; report which submethod is used for keyboard-interactive.
-
Make ssh_config(5) IdentitiesOnly apply to keys obtained from a PKCS11Provider. Allows control of which keys are offered from tokens using IdentityFile.
-
Fixed case where buffers returned on vinvalbuf(9) path and we do not get woken when waiting for kva.
-
Fixed vfs(9) kva reserve to ensure that kva reserve is checked for.
-
Implement hardware flow control and enable it by default on vcc(4/sparc64).
-
Don't wake the vfs(9) cleaner and throw away pages unnecessarily when growing the buffer cache .
+
For netstart(8), use the compact version of the check for ifconfig(8)'able interfaces from install.sub.
+
Added sshd_config(5) AllowTcpForwarding "local" and "remote" keywords to enable just local or remote TCP forwarding.
+
ssh-add(1) -d will now delete the corresponding certificate too; the -k option will delete key only.
+
Fixed sshd(8) logging of authentication when privsep is enabled by adding explicit "Partial" state; report which submethod is used for keyboard-interactive.
+
Make ssh_config(5) IdentitiesOnly apply to keys obtained from a PKCS11Provider. Allows control of which keys are offered from tokens using IdentityFile.
+
Fixed case where buffers returned on vinvalbuf(9) path and we do not get woken when waiting for kva.
+
Fixed vfs(9) kva reserve to ensure that kva reserve is checked for.
+
Implement hardware flow control and enable it by default on vcc(4/sparc64).
+
Don't wake the vfs(9) cleaner and throw away pages unnecessarily when growing the buffer cache .
Added check to xf86-video-intel so server can fail with useful error message instead of segfaulting later.
-
dhclient(8) will now catch SIGHUP, SIGINT, SIGTERM, SIGUSR1, SIGUS2 and remove routes and the interface address before exiting.
-
netstart(8) will try harder to identify invalid interface names and emit an error message.
+
dhclient(8) will now catch SIGHUP, SIGINT, SIGTERM, SIGUSR1, SIGUS2 and remove routes and the interface address before exiting.
+
netstart(8) will try harder to identify invalid interface names and emit an error message.
-
Make sure gcc(1) no longer incorrectly optimises away "*volatile_ptr = *volatile_ptr;" constructs on platforms which can perform memory to memory transfers in a single instruction (i.e. m68k and vax).
-
Make the bgpd(8) error messages more user friendly.
-
If a particular bgpd(8) capability is bad, log the fact and ignore it, rather than return an error. Allows bringing up a session that have (e.g.) unexpected AFI,SAFI pairs in them.
-
Add RX TCP/UDP checksum offload support to gem(4).
+
Make sure gcc(1) no longer incorrectly optimises away "*volatile_ptr = *volatile_ptr;" constructs on platforms which can perform memory to memory transfers in a single instruction (i.e. m68k and vax).
+
Make the bgpd(8) error messages more user friendly.
+
If a particular bgpd(8) capability is bad, log the fact and ignore it, rather than return an error. Allows bringing up a session that have (e.g.) unexpected AFI,SAFI pairs in them.
+
Add RX TCP/UDP checksum offload support to gem(4).
Additional CA root certificates added from GeoTrust/Equifax, GoDaddy, StartCom, and Thawte.
-
Drain sndiod(8) midi port output buffer before closing it ensuring the last few bytes are not lost.
-
Drop clients using sndiod(8) midi ports when port is closed (eg. umidi disconnected); try to reopen it whenever a new client connects.
-
When sndiod(8) audio device is closed, mark it as closed before dropping connections. Stops clients attempting to reopen the device.
-
Process incoming sndiod(8) midi data on the fly, not by using an input fifo.
-
Don't exit sndiod(8) if midi control port is destroyed (it never is).
-
Removed retired ssl(8) Thawte/Verisign certificates and intermediate GoDaddy certificate.
-
Made cloned devices line up with the rest of the fstat(1) output.
+
Drain sndiod(8) midi port output buffer before closing it ensuring the last few bytes are not lost.
+
Drop clients using sndiod(8) midi ports when port is closed (eg. umidi disconnected); try to reopen it whenever a new client connects.
+
When sndiod(8) audio device is closed, mark it as closed before dropping connections. Stops clients attempting to reopen the device.
+
Process incoming sndiod(8) midi data on the fly, not by using an input fifo.
+
Don't exit sndiod(8) if midi control port is destroyed (it never is).
+
Removed retired ssl(8) Thawte/Verisign certificates and intermediate GoDaddy certificate.
+
Made cloned devices line up with the rest of the fstat(1) output.
In locale/ctype/en_US.UTF-8.src, corrected width of some characters in the Hebrew range (0590?05FF).
-
Fixed speakers on Apple MacBook Air 2010, they require gpio azalia(4) unmuting.
-
Support large MTUs on vio(4); added support for chaining several rx buffers when receiving large packets.
+
Fixed speakers on Apple MacBook Air 2010, they require gpio azalia(4) unmuting.
+
Support large MTUs on vio(4); added support for chaining several rx buffers when receiving large packets.
-
Added rtsx(4), a new driver for the Realtek RTS5209 card reader.
+
Added rtsx(4), a new driver for the Realtek RTS5209 card reader.
Remove setting an initial (assumed) baudrate upon driver attach for many network interface cards.
-
5.2 stability fix for interoperability problem with some newer Junipers: make sure that bgpd(8) ignores the "must be zero" flags correctly and ensure that they are always reset to zero when sending updates out. A source code patch is available.
-
Prevent iked(8) VPN traffic leakages in dual-stack hosts/networks by forcibly blocking IPv6 traffic.
-
Fixed wrong argument being passed to snmpd(8) control_dispatch_imsg().
-
5.2 stability fix for interoperability problem with some newer Junipers: make sure that bgpd(8) ignores the "must be zero" flags correctly and ensure that they are always reset to zero when sending updates out. A source code patch is available.
+
Prevent iked(8) VPN traffic leakages in dual-stack hosts/networks by forcibly blocking IPv6 traffic.
+
Fixed wrong argument being passed to snmpd(8) control_dispatch_imsg().
+
Changed scandir(3) "select" argument to match POSIX.
+
Fixed radeon(4) EXA issue, introduced in xf86-video-ati 6.14.5 with accelerated solid pictures support.
-
Support the 47 and 1047 SM and RM sequences (alternate tmux(1) screen without cursor).
-
Added mg(1) "make-directory" (not bound to any shortcut).
-
Allow dhclient(8) "request", "require" and "ignore" as requests to create empty lists of options. Enables the removal of built-in lists or the removal of global lists inside an "interface" declaration.
-
Correctly aggregate together errors from nested tmux(1) config files with source-file.
-
Overriding a previous dhclient(8) ignore list will no longer leave incorrect ACTION flags lying around.
-
Allow tmux(1) cmd-run-shell to accept -t option to specify the pane to display the output.
-
When scrolling in copy mode with the mouse, scroll tmux(1) screen rather than moving cursor.
-
Update to drm(4) libdrm 2.4.31 and add the (non-yet-linked) libkms.
-
Don't toss away an existing dhclient(8) request/require list unless new list is successfully parsed.
-
Fix tmux(1) session choice so that preferring unattached sessions works.
+
Support the 47 and 1047 SM and RM sequences (alternate tmux(1) screen without cursor).
+
Added mg(1) "make-directory" (not bound to any shortcut).
+
Allow dhclient(8) "request", "require" and "ignore" as requests to create empty lists of options. Enables the removal of built-in lists or the removal of global lists inside an "interface" declaration.
+
Correctly aggregate together errors from nested tmux(1) config files with source-file.
+
Overriding a previous dhclient(8) ignore list will no longer leave incorrect ACTION flags lying around.
+
Allow tmux(1) cmd-run-shell to accept -t option to specify the pane to display the output.
+
When scrolling in copy mode with the mouse, scroll tmux(1) screen rather than moving cursor.
+
Update to drm(4) libdrm 2.4.31 and add the (non-yet-linked) libkms.
+
Don't toss away an existing dhclient(8) request/require list unless new list is successfully parsed.
+
Fix tmux(1) session choice so that preferring unattached sessions works.
-
ppp(8) panics if M_ZEROIZE gets set on readonly mbufs - use M_PROTO1 and M_LINK0 instead.
+
ppp(8) panics if M_ZEROIZE gets set on readonly mbufs - use M_PROTO1 and M_LINK0 instead.
-
em(4) pch2/82579 fixes: modify em_oem_bits_config_pchlan for pch2; sync pch2 use of gating/un-gating hardware phy config; add 82579 phy workarounds; enable Energy Efficient Ethernet on 82579.
-
Make ldomctl(8/sparc64) work on UltraSPARC T2. Enough functionality to create a configuration for a t5120 running System Firmware 7.1.x.
-
Make it a dhclient(8) syntax error to attempt to store an option in a list more than once.
-
ldomctl(8/sparc64) will now properly remove virtual device ports if we remove the associated channels.
-
Do not require, request, or ignore dhclient(8) DHO_PAD ("pad") and DHO_END ("option-end").
+
em(4) pch2/82579 fixes: modify em_oem_bits_config_pchlan for pch2; sync pch2 use of gating/un-gating hardware phy config; add 82579 phy workarounds; enable Energy Efficient Ethernet on 82579.
+
Make ldomctl(8/sparc64) work on UltraSPARC T2. Enough functionality to create a configuration for a t5120 running System Firmware 7.1.x.
+
Make it a dhclient(8) syntax error to attempt to store an option in a list more than once.
+
ldomctl(8/sparc64) will now properly remove virtual device ports if we remove the associated channels.
+
Do not require, request, or ignore dhclient(8) DHO_PAD ("pad") and DHO_END ("option-end").
Recognise a wrong network configuration that causes mvme88k tftpboot to stall, inform user what to do.
-
Clean up parsing of dhclient(8) option lists: syntactically incorrect request statements in dhclient.conf(5) are ignored; pass size of buffer being filled instead of assuming 256; always zero the passed in buffer; check for out of bounds index prior to using it.
+
Clean up parsing of dhclient(8) option lists: syntactically incorrect request statements in dhclient.conf(5) are ignored; pass size of buffer being filled instead of assuming 256; always zero the passed in buffer; check for out of bounds index prior to using it.
Don't assign the "host" MAC address to sparc64 virtual switch ports or print address for those ports.
-
Don't segfault if no dhclient(8) subnet-mask is provided, or is marked "ignore" in dhclient.conf(5); always zero out stack masks rather than using stack garbage when no subnet-mask is provided.
-
make(1) fixes: be more strict in recognising .if keyword() constructs; don't ignore unknown keywords; uniform white space handling; don't output a "." at the end of directory; complement "need an operator" fatal error message with the actual line content.
+
Don't segfault if no dhclient(8) subnet-mask is provided, or is marked "ignore" in dhclient.conf(5); always zero out stack masks rather than using stack garbage when no subnet-mask is provided.
+
make(1) fixes: be more strict in recognising .if keyword() constructs; don't ignore unknown keywords; uniform white space handling; don't output a "." at the end of directory; complement "need an operator" fatal error message with the actual line content.
-
Make login_yubikey(8) hex and modhex decoding case insensitive, to avoid shift/caps lock issues.
-
Handle up to 256 different interrupt vectors on cbus(4/sparc64). This is enough for 128 channels.
-
Replace aucat(1) server by a new sndiod(8) daemon that is simpler, smaller and faster.
-
Make the aucat(1) client wait for the first flow control message rather than assuming it can send a full initial data buffer.
+
Make the aucat(1) client wait for the first flow control message rather than assuming it can send a full initial data buffer.
Update to libxcb 1.9.0.
Sparc64 attempting to eject a CD-ROM makes the SCSI midlayer generate a READ_TOC command. Silently fail that command instead of spamming the console.
-
Fixed relayd(8) strtonum(), as it can only handle a maximum of LLONG_MAX.
-
Try to negotiate version 1.1 of the vDisk protocol to get vdsk(4/sparc64) media type and fake a CD-ROM drive.
-
Delete oce(4) rx refill timeouts when bringing an interface down.
-
D-Link DUB-E100 rev C1 now recognised by axe(4).
-
Made the mips and powerpc gcc(1) optimiser bug workarounds permanent (i.e. applied them to all platforms).
-
Allow "smtpctl(8) show queue" to run in "online" mode if the smtpd(8) server is running.
+
D-Link DUB-E100 rev C1 now recognised by axe(4).
+
Made the mips and powerpc gcc(1) optimiser bug workarounds permanent (i.e. applied them to all platforms).
+
Allow "smtpctl(8) show queue" to run in "online" mode if the smtpd(8) server is running.
-
Do not crash on stray .Ta macros mandoc(1) finds outside column lists.
-
Fixed gcc(1) passing of struct by value on m68k. Lets gcc(1) version 3 reliably bootstrap itself now.
-
Added atomic 32-bit cas operations to amd64 and i386. Needed for future acpi(4) global locking routines.
-
Added tmux(1) halfpage commands to mode command string table.
-
Use a utility function to show errors in tmux(1) config file.
+
Do not crash on stray .Ta macros mandoc(1) finds outside column lists.
+
Fixed gcc(1) passing of struct by value on m68k. Lets gcc(1) version 3 reliably bootstrap itself now.
+
Added atomic 32-bit cas operations to amd64 and i386. Needed for future acpi(4) global locking routines.
+
Added tmux(1) halfpage commands to mode command string table.
+
Use a utility function to show errors in tmux(1) config file.
If uvm_km_kmemalloc_pla() fails when just creating a thread (and not a process), then don't decrement the total and per-user counts of processes.
-
In mandoc(1) -Tman mode, support automatic word "keeps" in the SYNOPSIS (like -Tascii mode); don't escape the blank characters terminating man(7) macros.
-
Make mandoc(1) generated man(7) code more portable by using .PD instead of .sp -1v.
-
Don't output "$action not supported" when running rc.d(8) script from /etc/rc(8). Prevents warning at shutdown time when the script has rc_stop=NO.
+
In mandoc(1) -Tman mode, support automatic word "keeps" in the SYNOPSIS (like -Tascii mode); don't escape the blank characters terminating man(7) macros.
+
Make mandoc(1) generated man(7) code more portable by using .PD instead of .sp -1v.
+
Don't output "$action not supported" when running rc.d(8) script from /etc/rc(8). Prevents warning at shutdown time when the script has rc_stop=NO.
Small i386 memcpy optimisations to avoid unnecessary locks.
-
Ensure that the base provided to strtol(3) is between 2 and 36 inclusive, or the special value of 0.
+
Ensure that the base provided to strtol(3) is between 2 and 36 inclusive, or the special value of 0.
Don't map a buffer (and potentially sleep) when invalidating it in vinvalbuf. Fixes a problem where we could sleep for kva, leading to invalid pointers on the next pass through the loop.
-
Simplify vio(4) vio_iff(), set own MAC in unicast MAC filter (needed by virtualbox).
-
Don't send iwn(4) with "advanced" bluetooth coexistence the configure coexistence command. Avoids firmware crash.
-
Added initial iwn(4) support for Intel Centrino Wireless-N 1030.
+
Simplify vio(4) vio_iff(), set own MAC in unicast MAC filter (needed by virtualbox).
+
Don't send iwn(4) with "advanced" bluetooth coexistence the configure coexistence command. Avoids firmware crash.
+
Added initial iwn(4) support for Intel Centrino Wireless-N 1030.
-
Warn about unknown volume/arch in mandoc(1) Dt macro arguments.
-
Third implementation of m88k gcc(1) varags (upstream version still wrong).
-
Fixed mandoc(1) for .Ap and .In trailing delimiters. Fixes the end of sentence spacing in open(2).
-
Improve mandoc(1) formatting of badly nested font blocks.
-
Run dhclient(8) discover_interface() before forking, so both processes will know the interface information.
-
Added missing "break;" so that IFT_ETHER dhclient(8) routes are deleted as intended.
-
Fixed mandoc(1) crash triggered by .Bl -tag .It Xo .El .Sh.
+
Warn about unknown volume/arch in mandoc(1) Dt macro arguments.
+
Third implementation of m88k gcc(1) varags (upstream version still wrong).
+
Fixed mandoc(1) for .Ap and .In trailing delimiters. Fixes the end of sentence spacing in open(2).
+
Improve mandoc(1) formatting of badly nested font blocks.
+
Run dhclient(8) discover_interface() before forking, so both processes will know the interface information.
+
Added missing "break;" so that IFT_ETHER dhclient(8) routes are deleted as intended.
+
Fixed mandoc(1) crash triggered by .Bl -tag .It Xo .El .Sh.
Print macppc UniNorth/U3 revision number (taken from openfirmware) to show which AGP chipset is present.
-
If max-prefix/restart are used in bgpctl(8), display the values in "bgpctl sh nei" output.
-
No longer try to transmit packets if the vr(4) interface is not running.
-
If dhclient(8) "-d" is specified, don't redirect privileged child's stdin/stdout/stderr to /dev/null.
+
If max-prefix/restart are used in bgpctl(8), display the values in "bgpctl sh nei" output.
+
No longer try to transmit packets if the vr(4) interface is not running.
+
If dhclient(8) "-d" is specified, don't redirect privileged child's stdin/stdout/stderr to /dev/null.
-
cwm(1) tab-complete bug fixed: once exec_path is completed, allow for subsequent completion.
+
Fixed dhclient(8) so "ignore subnet-mask;" will work.
+
Allocate an oce(4) mailbox payload dma memory upfront, instead of per request.
+
Added axe(4) support for the lenovo usb 2.0 ethernet adapter.
-
Avoid segfault in the unlikely event that a NULL device is passed to tcpdump(8) priv_pcap_live().
-
Allow the full range of unsigned serial numbers for ssh-keygen(1).
-
Fixed username passed to ssh(1) helper program; prepare stdio fds before closefrom().
+
Avoid segfault in the unlikely event that a NULL device is passed to tcpdump(8) priv_pcap_live().
+
Allow the full range of unsigned serial numbers for ssh-keygen(1).
+
Fixed username passed to ssh(1) helper program; prepare stdio fds before closefrom().
Adjust Makefile.cross to allow cross-gcc to build using different compiler version than the target.
-
Do an oce(4) OACTIVE/if_start dance only once per tx interrupt.
-
Enabled hardware tx checksum offloading for oce(4).
-
npppd(8) can now handle file descriptor exhaustion in the accept() case.
-
Correct the first argument of agpmmap(), making possible to mmap the agp(4) aperture.
-
Make sure smtpd(8) does not miss the last envelope.
-
Allow bgpd.conf(5) filtering based on NEXTHOP attribute (eg "allow from any nexthop neighbor").
+
Do an oce(4) OACTIVE/if_start dance only once per tx interrupt.
+
Enabled hardware tx checksum offloading for oce(4).
+
npppd(8) can now handle file descriptor exhaustion in the accept() case.
+
Correct the first argument of agpmmap(), making possible to mmap the agp(4) aperture.
+
Make sure smtpd(8) does not miss the last envelope.
+
Allow bgpd.conf(5) filtering based on NEXTHOP attribute (eg "allow from any nexthop neighbor").
-
smtpd(8) improvements: log more events, with each messages prefixed with a token to identify its class; implement "smtpctl(8) monitor" to display updates of selected internal counters; when reloading the on-disk queue at startup no longer commits a message if no envelope was submitted for that message.
-
fmt_scaled(3) now sets errno to EINVAL (not ERANGE) if it hits an invalid multiplier, to match man page.
-
smtpd(8) improvements: log more events, with each messages prefixed with a token to identify its class; implement "smtpctl(8) monitor" to display updates of selected internal counters; when reloading the on-disk queue at startup no longer commits a message if no envelope was submitted for that message.
+
fmt_scaled(3) now sets errno to EINVAL (not ERANGE) if it hits an invalid multiplier, to match man page.
+
Once a rdist(1) C_RECVDIR command is sent, send matching C_END command later, even if opendir() fails or nodescend option is set.
-
Fix various rdist(1) and rdistd(1) format string issues. Stop assuming time_t is long or smaller. Enable warnings.
+
Once a rdist(1) C_RECVDIR command is sent, send matching C_END command later, even if opendir() fails or nodescend option is set.
+
Fix various rdist(1) and rdistd(1) format string issues. Stop assuming time_t is long or smaller. Enable warnings.
Fix pid matching on kernel crashdumps.
-
Added support for the Intel Centrino Advanced-N 6235 to iwn(4).
-
Stopped mg(1) updating character offset on the line all the time (astoundingly hostile to slow terminals).
-
Fix dhclient.conf(5) "default" directive (broken in code refactoring).
-
dhclient(8) supersede/append/prepend actions works again even if the dhcp(8) server doesn't send any data for the affected option (broken when the supersede/append/prepend/ignore logic was re-factored).
+
Added support for the Intel Centrino Advanced-N 6235 to iwn(4).
+
Stopped mg(1) updating character offset on the line all the time (astoundingly hostile to slow terminals).
+
Fix dhclient.conf(5) "default" directive (broken in code refactoring).
+
dhclient(8) supersede/append/prepend actions works again even if the dhcp(8) server doesn't send any data for the affected option (broken when the supersede/append/prepend/ignore logic was re-factored).
Try to load the gallium3d "swrastg" driver if available, before falling back to the default mesa "swrast" one for software rendering.
-
Rewrote axe(4) and smsc(4) receive filter handling code; cleaned up the ioctl.
-
prevent athn(4) calling athn_detach unnecessarily if shared code was not initialised.
-
Enhanced sysmerge(8) error_rm_wrkdir() to print an error message if one is passed as an argument.
-
Read CPU frequency from the fixed-function performance counter of on x86 chips with constant time stamp counters. Lets sysctl(8) hw.cpuspeed and hw.setperf reflect correct values.
+
Rewrote axe(4) and smsc(4) receive filter handling code; cleaned up the ioctl.
+
prevent athn(4) calling athn_detach unnecessarily if shared code was not initialised.
+
Enhanced sysmerge(8) error_rm_wrkdir() to print an error message if one is passed as an argument.
+
Read CPU frequency from the fixed-function performance counter of on x86 chips with constant time stamp counters. Lets sysctl(8) hw.cpuspeed and hw.setperf reflect correct values.
-
Per POSIX, fix raise(3) and abort(3) to send the signal to the current thread.
-
Don't sync oce(4) dma memory for the whole ring when updating a single entry.
-
Ported most gcc(1) version 2.95 m88k fixes to the gcc(1) version 3 codebase.
-
No longer disable VLAN promiscuous mode, so oce(4) can receive ethernet packets with VLAN tags.
-
libtool(1) now properly filters symbols on elf(5) systems; runs nm(1) on every object and static library we might need, so we don't lose anything; allows for the result to be empty.
-
Fixed libtool(1) get_symbollist: output completely empty file if no symbol; and more debug info.
+
Per POSIX, fix raise(3) and abort(3) to send the signal to the current thread.
+
Don't sync oce(4) dma memory for the whole ring when updating a single entry.
+
Ported most gcc(1) version 2.95 m88k fixes to the gcc(1) version 3 codebase.
+
No longer disable VLAN promiscuous mode, so oce(4) can receive ethernet packets with VLAN tags.
+
libtool(1) now properly filters symbols on elf(5) systems; runs nm(1) on every object and static library we might need, so we don't lose anything; allows for the result to be empty.
+
Fixed libtool(1) get_symbollist: output completely empty file if no symbol; and more debug info.
-
oce(4) driver now matches hardware, to support mtu values from 256 up to 9000.
-
When halting the oce(4) rx engine, avoid firmware DMA'ing into the freed cluster.
-
Close dhclient(8) routing socket fd leak when deleting old address.
+
Fix arp(8) so "route -Tx exec arp -an" uses the process rdomain, but still allow command line overrides.
+
Don't depend on IFCAP_CSUM flags when configuring ix(4) rx checksumming; corrected an incorrect usage of IXGBE_RXCSUM_PCSD.
-
Plugged cwm(1) leak when using "unmap" for kbd/mouse bindings.
-
Fix vfs(9) and uvm(9) to allow the cleaner and syncer to run even when under intense memory or kernel virtual address pressure; correct cleaner and sleep/wakeup cases when memory and kva are low.
+
Plugged cwm(1) leak when using "unmap" for kbd/mouse bindings.
+
Fix vfs(9) and uvm(9) to allow the cleaner and syncer to run even when under intense memory or kernel virtual address pressure; correct cleaner and sleep/wakeup cases when memory and kva are low.
Enable %tick access for userland on sparc64 sun4u systems.
-
Properly clear the dhclient(8) UP flag when forcing interface down/up, rather than setting all flags to zero.
-
Make ldomd(8) consume ACKs when doing large sends.
-
ldomctl(8) support for listing/selecting configurations store on the SP.
-
Call service start function if a particular ldomd(8) domain service has been successfully registered.
+
Properly clear the dhclient(8) UP flag when forcing interface down/up, rather than setting all flags to zero.
+
Make ldomd(8) consume ACKs when doing large sends.
+
ldomctl(8) support for listing/selecting configurations store on the SP.
+
Call service start function if a particular ldomd(8) domain service has been successfully registered.
Include declaration of sparcDriverName() to fix segfault on sunffb graphics.
Switch mvme68k to timecounters.
-
Remove default of AuthorizedCommandUser from sshd_config(5). Administrators are now expected to explicitly specify a user.
+
Remove default of AuthorizedCommandUser from sshd_config(5). Administrators are now expected to explicitly specify a user.
-
Stop dhclient(8) and resolv.conf(5) passing interface names around needlessly when creating/flushing routes.
-
Fixes for resolv.conf(5) handling: Don't leak a file descriptor if there are no contents for resolv.conf(5), and delete this file if it is zero-length; allow for only resolv.conf.tail to go into resolv.conf.
-
Fixed potential mg(1) memory leak, found by llvm.
-
Don't leak a mg(1) file descriptor when testing for permissions; make sure directory is executable, otherwise we can't list it.
+
Stop dhclient(8) and resolv.conf(5) passing interface names around needlessly when creating/flushing routes.
+
Fixes for resolv.conf(5) handling: Don't leak a file descriptor if there are no contents for resolv.conf(5), and delete this file if it is zero-length; allow for only resolv.conf.tail to go into resolv.conf.
+
Fixed potential mg(1) memory leak, found by llvm.
+
Don't leak a mg(1) file descriptor when testing for permissions; make sure directory is executable, otherwise we can't list it.
-
Introduce better and simpler oce(4) producer/consumer queue iterator implementation.
-
Remove 13 years old compiler bug workaround in m68k pwd_mkdb(8) code.
-
Avoid some misaligned accesses. Lets dhclient(8) work again on sparc64.
-
Added smtpd(8) "kick counter" to detect and disconnect clients that hog the session.
-
New malloc(3) option "U" to "free unmap": guards/unmaps freed allocations without disabling chunk randomisation. Offers better defence against "heap feng shui" style attacks.
-
Stop dhclient(8) adding a "nameserver" line to resolv.conf(5) if the nameserver in question is the empty string.
-
Consistency and robustness improvements in smtpd(8) mda.
-
Make smtpd(8) counters more informative in the scheduler: number of envelopes added or cancelled; properly report envelope counts, as well as the outcome of deliveries.
-
Watch the non-privileged end of the pipe to the privileged dhclient(8) child process. So when the child dies, the parent exits immediately.
-
Include tcp/udp.h unconditionally to unbreak rd(4).
-
Don't let aucat(1) insert twice recorded wav files (-o) on the list of recorded files.
-
Fixed aucat(1) crashes when wav_close() is called on uninitialised wav structure.
-
Use dedicated messages for flow control (instead of clock tick) and enable flow control for aucat(1) MIDI.
+
Introduce better and simpler oce(4) producer/consumer queue iterator implementation.
+
Remove 13 years old compiler bug workaround in m68k pwd_mkdb(8) code.
+
Avoid some misaligned accesses. Lets dhclient(8) work again on sparc64.
+
Added smtpd(8) "kick counter" to detect and disconnect clients that hog the session.
+
New malloc(3) option "U" to "free unmap": guards/unmaps freed allocations without disabling chunk randomisation. Offers better defence against "heap feng shui" style attacks.
+
Stop dhclient(8) adding a "nameserver" line to resolv.conf(5) if the nameserver in question is the empty string.
+
Consistency and robustness improvements in smtpd(8) mda.
+
Make smtpd(8) counters more informative in the scheduler: number of envelopes added or cancelled; properly report envelope counts, as well as the outcome of deliveries.
+
Watch the non-privileged end of the pipe to the privileged dhclient(8) child process. So when the child dies, the parent exits immediately.
+
Include tcp/udp.h unconditionally to unbreak rd(4).
+
Don't let aucat(1) insert twice recorded wav files (-o) on the list of recorded files.
+
Fixed aucat(1) crashes when wav_close() is called on uninitialised wav structure.
+
Use dedicated messages for flow control (instead of clock tick) and enable flow control for aucat(1) MIDI.
When possible, have vcc(4/spar64) send multiple characters per packet; stop sending when the transmit queue is full; set a timeout to avoid stalling.
+
When possible, have vcc(4/spar64) send multiple characters per packet; stop sending when the transmit queue is full; set a timeout to avoid stalling.
-
Stopped acpitz(4) showing Kelvin units; fixed Celsius measures (no longer off by a factor of 10).
-
Forcibly delete all existing ipv4 addresses from an interface as dhclient(8) binds new lease to that interface. Fixes unexpectedly persistent addresses and failures of dhclient(8) when switching an interface repeatedly between different networks.
-
Stopped acpitz(4) showing Kelvin units; fixed Celsius measures (no longer off by a factor of 10).
+
Forcibly delete all existing ipv4 addresses from an interface as dhclient(8) binds new lease to that interface. Fixes unexpectedly persistent addresses and failures of dhclient(8) when switching an interface repeatedly between different networks.
+
Add support for Intel's Supervisor Mode Access Prevention (SMAP) feature to i386 and amd64.
-
Some fixes for the vio(4) receive filter handling.
-
New sshd_config(5) option AuthorizedKeysCommand to support fetching authorized_keys from a command in addition to (or instead of) from the filesystem.
-
Removed dhclient-script(8) and dhclient.conf(5) "script" directive. Do all interface and route configuration via ioctl's and routing sockets.
-
Prevent underflows in pfsync(4) and pflow(4) by using signed variables.
-
Use monotonic time_uptime for pfsync(4) and pflow(4) expiration values as time_second can be skewed at runtime.
-
Bump the default number of descriptors in ix(4).
+
Some fixes for the vio(4) receive filter handling.
+
New sshd_config(5) option AuthorizedKeysCommand to support fetching authorized_keys from a command in addition to (or instead of) from the filesystem.
+
Removed dhclient-script(8) and dhclient.conf(5) "script" directive. Do all interface and route configuration via ioctl's and routing sockets.
+
Prevent underflows in pfsync(4) and pflow(4) by using signed variables.
+
Use monotonic time_uptime for pfsync(4) and pflow(4) expiration values as time_second can be skewed at runtime.
+
Added support for Elantech touchpads to pms(4), so X synaptics(4) driver can configure these touchpads properly.
+
Teach wsconsctl(8) about the elantech mouse type.
-
Limit the number of smtpd(8) messages/recipients that can be enqueued on a single SMTP connection.
+
Limit the number of smtpd(8) messages/recipients that can be enqueued on a single SMTP connection.
-
Changed dhclient.conf(5) directive 'ignore' to take a list of option names rather than list of option declarations. e.g. "ignore routers;" instead of "ignore routers 1.2.3.4;"
-
Made it possible to use ldomctl(8) to reconfigure when ldomd(8) is running.
-
Fix ldomd(8) var-config response messages. Makes OpenBoot stop complaining about not being able to update LDOM variables.
-
Use ldomd(8) to provide the var-config domain service to all the currently configured guest domains.
-
Give ldomd(8) its own copy of the domain services support code and modify it to handle multiple channels.
-
All softraid(4)boot(8) support is now enabled by default, including support for booting from crypto volumes. Can be completely enabled or disabled at compile time.
-
Made sndio(7) midi code use non-blocking i/o like the other audio code.
-
Check that sndio(7) polled fd number is smaller than SIO_MAXNFDS, and crank maximums.
+
Changed dhclient.conf(5) directive 'ignore' to take a list of option names rather than list of option declarations. e.g. "ignore routers;" instead of "ignore routers 1.2.3.4;"
+
Made it possible to use ldomctl(8) to reconfigure when ldomd(8) is running.
+
Fix ldomd(8) var-config response messages. Makes OpenBoot stop complaining about not being able to update LDOM variables.
+
Use ldomd(8) to provide the var-config domain service to all the currently configured guest domains.
+
Give ldomd(8) its own copy of the domain services support code and modify it to handle multiple channels.
+
All softraid(4)boot(8) support is now enabled by default, including support for booting from crypto volumes. Can be completely enabled or disabled at compile time.
+
Made sndio(7) midi code use non-blocking i/o like the other audio code.
+
Check that sndio(7) polled fd number is smaller than SIO_MAXNFDS, and crank maximums.
-
For sparc64 devices that attach to cbus(4/sparc64), disable interrupts up-front and explicitly enabling them later than the other way around.
-
Fix the oce(4) multicast filter full size check.
-
Bugfix for userland program attempting to do a semop(2). Kernel returns ENOSPC rather than panics.
-
Repaired maestro(4) pci powerstate handling and resumes.
-
Add the IP_DIVERTFL socket option on divert(4) sockets to control which packets (as in direction) of the traffic will be diverted through the divert socket.
-
Add domain services support code to ldomctl(8) and use it to fetch the PRI (Physical Resource Inventory) from the service processor.
+
Fix the oce(4) multicast filter full size check.
+
Bugfix for userland program attempting to do a semop(2). Kernel returns ENOSPC rather than panics.
+
Repaired maestro(4) pci powerstate handling and resumes.
+
Add the IP_DIVERTFL socket option on divert(4) sockets to control which packets (as in direction) of the traffic will be diverted through the divert socket.
+
Add domain services support code to ldomctl(8) and use it to fetch the PRI (Physical Resource Inventory) from the service processor.
-
Disallow pf.conf(5) tables and address pools for rdr-to, nat-to and route-to with any other scheduling algorithms than round-robin or least-states. Stops pfctl(8) accepting invalid address pools.
+
Disallow pf.conf(5) tables and address pools for rdr-to, nat-to and route-to with any other scheduling algorithms than round-robin or least-states. Stops pfctl(8) accepting invalid address pools.
-
Cleaned up more of the pckbc(4) driver soft-state when suspending.
-
In sd(4), do a flush of the disk before hibernate to clear the buffer cache.
-
Limit the number of per-user mda (external program) deliveries that smtpd(8) can be running at the same time, to cope with long-running filters in .forward file.
-
Limit number of envelopes sent by the smtpd(8) queue to the mda, to avoid file descriptor exhaustion.
+
Limit the number of per-user mda (external program) deliveries that smtpd(8) can be running at the same time, to cope with long-running filters in .forward file.
+
Limit number of envelopes sent by the smtpd(8) queue to the mda, to avoid file descriptor exhaustion.
Beginning of ldomctl tool, to control sun4v logical domains. Currently can start and stop domains.
-
smtpd(8) will now enforce different permissions on different files in ssl_load_file().
+
smtpd(8) will now enforce different permissions on different files in ssl_load_file().
-
Avoid some unnecessary aliases expansion in smtpd(8).
-
Move xl(4) WOL activation to DVACT_POWERDOWN (instead of doing it twice).
-
Stop xl(4) putting itself into D3 mode when going to WOL; allow pci(4) subsystem to do that based on BIOS information if it needs to.
-
When smtpd(8) makemap is executed in sendmail mode, check if ".db" is part of the filename and imply it otherwise so "makemap hash /etc/mail/aliases < aliases" works.
-
smtpd(8) alias expansion and ruleset matching code now checks for failure to distinguish between "no match" and "internal error" (e.g. missing or broken db file)
-
Implement mg(1) "revert-buffer", which reverts the current buffer to on-disk copy.
+
Avoid some unnecessary aliases expansion in smtpd(8).
+
Move xl(4) WOL activation to DVACT_POWERDOWN (instead of doing it twice).
+
Stop xl(4) putting itself into D3 mode when going to WOL; allow pci(4) subsystem to do that based on BIOS information if it needs to.
+
When smtpd(8) makemap is executed in sendmail mode, check if ".db" is part of the filename and imply it otherwise so "makemap hash /etc/mail/aliases < aliases" works.
+
smtpd(8) alias expansion and ruleset matching code now checks for failure to distinguish between "no match" and "internal error" (e.g. missing or broken db file)
+
make(1) changes: put back some job control that's necessary when we don't run a shell; improved debugging and -p output to sort variables, targets, rules, output stuff in a nicer format mimicing input; better error message when no command is found, explain where the target comes from; sort final error list by file; show system files in errors as ; reincorporate random delay; and optimise siginfo output by not regenerating the whole string each time.
-
Allow tmux(1) session tree (C-b s) to expand and collapse sessions with left/right/space keys.
-
Fixed ssh(1) -z option, broken in revision 1.215.
+
make(1) changes: put back some job control that's necessary when we don't run a shell; improved debugging and -p output to sort variables, targets, rules, output stuff in a nicer format mimicing input; better error message when no command is found, explain where the target comes from; sort final error list by file; show system files in errors as <bsd.prog.mk>; reincorporate random delay; and optimise siginfo output by not regenerating the whole string each time.
+
Allow tmux(1) session tree (C-b s) to expand and collapse sessions with left/right/space keys.
+
Fixed ssh(1) -z option, broken in revision 1.215.
-
Add some random PEN (private enterprise numbers) to snmpd(8).
-
Support 0.0.0.0 and 255.255.255.255 IPv4 addresses in snmpd(8). Fixes aborting address traversal / SNMP walk when an "any"/0.0.0.0 address was configured on an interface.
+
Add some random PEN (private enterprise numbers) to snmpd(8).
+
Support 0.0.0.0 and 255.255.255.255 IPv4 addresses in snmpd(8). Fixes aborting address traversal / SNMP walk when an "any"/0.0.0.0 address was configured on an interface.
-
When outputting to stdout and compress(1) would grow the file, exit normally instead of with a value of 2. Also avoids unlinking the file "stdout" in the current directory in this case.
-
Added decision to the smtpd(8) rule so that we can properly perform a "reject from" or "accept from" match.
+
When outputting to stdout and compress(1) would grow the file, exit normally instead of with a value of 2. Also avoids unlinking the file "stdout" in the current directory in this case.
+
Added decision to the smtpd(8) rule so that we can properly perform a "reject from" or "accept from" match.
-
Fixed baud rate setting on uslcom(4) CP1201/2/3 devices; add support for hardware flow control.
+
Fixed baud rate setting on uslcom(4) CP1201/2/3 devices; add support for hardware flow control.
-
Fix address family for ipv6 bpf(4) packet capture in pipex(4).
+
Fix address family for ipv6 bpf(4) packet capture in pipex(4).
Add support for the Adaptec 39320LPE controller.
When merging messages from an update, and message already exists in the main queue, don't count it twice.
-
Use a smaller buffer size when not attached to a high speed/usb2 controller. Fixes smsc(4) with usb1 controllers.
-
Better tmux(1) test for when recovering current working directory.
+
Use ACS characters for tmux(1) choose-tree arrows.
-
Allow route(8) -T 3 add to create a table even if the table does not exist yet. The only way to create alternate routing tables.
-
Enable bgpd(8) graceful restart by default. Disabled per neighbour with "announce restart no".
+
Allow route(8) -T 3 add to create a table even if the table does not exist yet. The only way to create alternate routing tables.
+
Enable bgpd(8) graceful restart by default. Disabled per neighbour with "announce restart no".
Unlink imake and cf from build. This now is in ports.
On i386, make sure we send MSIs to the primary CPU like we do on amd64.
-
Fix for VU#624931 CVE-2012-2978 to to 5.1-stable: nsd(8) denial of service vulnerability from non-standard DNS packet.
-
smtpd(8) now logs envelope status in a uniform way, automagically adding a rcpt= field if "dest" differs from the original "rcpt".
-
Fixed sftp(1) handling of filenames containing escaped globbing characters, and escape "#" and "*". Also, fixed improper handling of absolute paths when pwd(1) is part of the completed path.
-
relayd(8) file descriptor accounting for relays: reserve fds for unopened connections to backend servers.
-
Fix for VU#624931 CVE-2012-2978 to to 5.1-stable: nsd(8) denial of service vulnerability from non-standard DNS packet.
+
smtpd(8) now logs envelope status in a uniform way, automagically adding a rcpt=<user@domain> field if "dest" differs from the original "rcpt".
+
Fixed sftp(1) handling of filenames containing escaped globbing characters, and escape "#" and "*". Also, fixed improper handling of absolute paths when pwd(1) is part of the completed path.
+
relayd(8) file descriptor accounting for relays: reserve fds for unopened connections to backend servers.
+
Fixed ospf6d(8) kroute code to read the scope of the route correctly.
-
pfsync(4) now restores carp(4) demotions, so it won't leave the machine in a demoted state.
+
Fixed ospf6d(8) kroute code to read the scope of the route correctly.
+
pfsync(4) now restores carp(4) demotions, so it won't leave the machine in a demoted state.
Don't filter spanning tree BPDUs. Either process, or forward them (avoids bridging loops).
-
Added driver for Toradex OAK usb sensors: uoaklux(4): LUX USB illuminance sensor; uoakrh(4) USB temperature and relative humidity sensor; uoakv(4) USB +/- 10V 8channel ADC interface.
-
Allow ntpd.conf(5) to assign a stratum to a sensor with the syntax "stratum ".
-
Be consistent between installer and useradd(8), and put newly created users into their own primary group. Does not change existing installations that already have a usermgmt.conf(5).
-
Lower pf.conf(5) frags limit. Avoids running out of mbuf clusters when dealing with lots of IP fragments.
+
Added driver for Toradex OAK usb sensors: uoaklux(4): LUX USB illuminance sensor; uoakrh(4) USB temperature and relative humidity sensor; uoakv(4) USB +/- 10V 8channel ADC interface.
+
Allow ntpd.conf(5) to assign a stratum to a sensor with the syntax "stratum <level>".
+
Be consistent between installer and useradd(8), and put newly created users into their own primary group. Does not change existing installations that already have a usermgmt.conf(5).
+
Lower pf.conf(5) frags limit. Avoids running out of mbuf clusters when dealing with lots of IP fragments.
-
Set up i386/amd64 pci(4) bus number resource accounting for the main PCI bus hierarchy.
-
Add resource tracking for pci(4) bus numbers. Stops attaching the same bus twice.
+
Set up i386/amd64 pci(4) bus number resource accounting for the main PCI bus hierarchy.
+
Add resource tracking for pci(4) bus numbers. Stops attaching the same bus twice.
Add i386/amd64 support for the rdrand instruction found in recent Intel processors.
-
When a socket(2) is spliced, it may not wakeup the userland for reading. Avoids race condition.
-
Added drivers for virtio(4) network (vio(4)) and block devices (vioblk(4), the disks attach as scsi disks).
-
Fix relayd(8) ICMP checks by setting the socklen correctly before calling recvfrom().
+
When a socket(2) is spliced, it may not wakeup the userland for reading. Avoids race condition.
+
Added drivers for virtio(4) network (vio(4)) and block devices (vioblk(4), the disks attach as scsi disks).
+
Fix relayd(8) ICMP checks by setting the socklen correctly before calling recvfrom().
-
Several tweaks to make mpi(4) work for vmware emulated sas adapters, and improved error reporting.
-
Once resolv.conf.saved has been copied back as resolv.conf(5), delete so it isn't copied again the next time a dhclient(8) goes away.
-
Support the Lenovo ThinkVision LT1421 (portable displaylink monitor) with udl(4).
-
Added udl(4) support for 1366x768 widescreen displays.
-
Wait until all pci(4) transfers have finished before giving up DMA buffer mappings.
-
New configuration syntax for npppd(8). npppd.conf based on parse.y; npppd-users based on getcap(3).
-
Improved xf86-video-intel hack to restore text mode on ironlake/sandy bridge.
-
Ensure we have at least two smtpd(8) descriptors per-client accepted, to avoid fatal when client sends DATA, and we don't have a descriptor for it.
+
Ensure we have at least two smtpd(8) descriptors per-client accepted, to avoid fatal when client sends DATA, and we don't have a descriptor for it.
-
Allow smtpd(8) queueing to work properly when IPv6 disabled.
-
Encode ipsecctl(8) transform parameters in the transform name, too. Unbreaks setups that allow multiple transforms for a connection.
+
Allow smtpd(8) queueing to work properly when IPv6 disabled.
+
Encode ipsecctl(8) transform parameters in the transform name, too. Unbreaks setups that allow multiple transforms for a connection.
m88k does not have the m68k long double type, so don't build long double libm routines.
-
Don't read the sndiod(8) xrun counter before the offset in the audio ring. Stops potential timing error.
-
When printing smtpd(8) ioev, do not segfault if there is no associated iobuf. Also give info about the cipher if there is an ssl(8) context.
-
Check limits before allocating the smtpd(8) session.
-
Tell make(1) that "!" is a shell reserved word, this lets "test: ! pgrep process" work, without trying to look for a '!' command.
+
Don't read the sndiod(8) xrun counter before the offset in the audio ring. Stops potential timing error.
+
When printing smtpd(8) ioev, do not segfault if there is no associated iobuf. Also give info about the cipher if there is an ssl(8) context.
+
Check limits before allocating the smtpd(8) session.
+
Tell make(1) that "!" is a shell reserved word, this lets "test: ! pgrep process" work, without trying to look for a '!' command.
Stop xinstall unlinking destination if we can't open the source file. Avoids race condition and fixes a problem with databases/ruby-ldap.
-
Fix malloc(3) precedence bug (& has lower precedence than !=).
+
Fix malloc(3) precedence bug (& has lower precedence than !=).
-
Simplify the way we call the rc.d(8) script in "restart".
-
Added mii(4) code to support recent chips which have phys in locations other than phy address 1.
+
Simplify the way we call the rc.d(8) script in "restart".
+
Added mii(4) code to support recent chips which have phys in locations other than phy address 1.
Define empty CDIAGFLAGS for programs that use Werror. Makes "make build" build with WARNINGS=Yes on amd64.
-
Fixed a sasyncd(8) race condition which would cause segfault.
-
Better bgpd(8) graceful restart support. Implements only the "Restarting Client" bits of the RFC. Off by default ("announce restart yes" to enable it).
-
Prevent detection of bogus libraries by ldconfig(8).
+
Fixed a sasyncd(8) race condition which would cause segfault.
+
Better bgpd(8) graceful restart support. Implements only the "Restarting Client" bits of the RFC. Off by default ("announce restart yes" to enable it).
+
Prevent detection of bogus libraries by ldconfig(8).
Cherry-pick upstream's commit to convert the openchrome driver for compatibility with xserver 1.13.
-
Simplify smtpd(8) scheduler by making it a quadratic delaying (delay derived from the retry count).
-
Initialise smtpd(8) fd correctly. Fixes many problems.
-
Plug a race where we're trying to kill a traced process while it is already exiting.
Bump amd64 CPU feature strings to 12 chars, since some names are now 8 characters long.
Call pci_min_powerstate() to determine the lowest possible powerstate instead of hardcoding it to D3.
-
Fixup a mpii(4) memory access fault on an invalid reply.
-
Make mg(1) C-r not screw up the line counter if the pattern ends up not matching.
+
Fixup a mpii(4) memory access fault on an invalid reply.
+
Make mg(1) C-r not screw up the line counter if the pattern ends up not matching.
Create IPv6 privacy addresses even if static IPv6 addresses are present. Restores ability to use privacy addresses for outgoing connections and static addresses for incoming connections (broken by r1.62).
-
Make ssh(1) muxmaster run with -N shut down gracefully when a client sends it "-O stop".
+
Make ssh(1) muxmaster run with -N shut down gracefully when a client sends it "-O stop".
-
Print '^Z' instead of a raw ^Z when the sequence is not supported by ssh(1).
+
Print '^Z' instead of a raw ^Z when the sequence is not supported by ssh(1).
Removed compat_aout support for i386.
Make all dos file names 11 byte array. Fixes "panic: smashed stack in msdosfs_rename.c".
-
Make the ssh(1) escape command help (~?) context sensitive, so only commands that will work in current session are shown.
-
shorter display for minor pkg_add(1) updatesets, "foo-0.0->foo-1.0" becomes "foo-0.0->1.0".
+
Make the ssh(1) escape command help (~?) context sensitive, so only commands that will work in current session are shown.
+
shorter display for minor pkg_add(1) updatesets, "foo-0.0->foo-1.0" becomes "foo-0.0->1.0".
-
Add ssh(1) ~v and ~V escape sequences to raise and lower the logging level respectively.
-
ksh(1) sh -c should not munge argv[]. Fixes ps(1) -ww output.
-
rm(1) will now overwrite with random stream (a repeating chunk of random data isn't random at all).
+
Add ssh(1) ~v and ~V escape sequences to raise and lower the logging level respectively.
+
ksh(1) sh -c should not munge argv[]. Fixes ps(1) -ww output.
+
rm(1) will now overwrite with random stream (a repeating chunk of random data isn't random at all).
COMPAT_O48 turned off in GENERIC kernel.
Implement basic (blocking) YP support for getaddrinfo_async(). YP is now supported on all relevant resolver functions.
-
Handle empty list properly in tmux(1) choose-list.
-
tmux(1) can't tell what a terminal has done with a DCS string, so reset cursor and attributes afterwards.
-
When running fw_update(1), don't let pkg_add(1) turn interactive, and waive the @ask-update questions.
+
Handle empty list properly in tmux(1) choose-list.
+
tmux(1) can't tell what a terminal has done with a DCS string, so reset cursor and attributes afterwards.
+
When running fw_update(1), don't let pkg_add(1) turn interactive, and waive the @ask-update questions.
-
rtadvd(8) config code no longer truncates a pointer to int, before checking the low bits.
-
rm(1) now only does one random overwrite, as this is deemed sufficient.
-
Use the correct index when adding item in tmux(1) choose-tree.
+
When choosing a pane found by tmux(1) find-window, switch to that pane rather than just the window.
+
Added cmd-choose-list to tmux(1), to allow arbitrary options to be selected.
+
Send notifications to control tmux(1) clients. Also don't redraw client when suspended.
+
Start with stdin disabled, so tmux(1) doesn't eat anything (eg pasting commands).
-
Unbreak compilation of umidi(4) when no DIAGNOSTICS are defined.
+
Unbreak compilation of umidi(4) when no DIAGNOSTICS are defined.
Make profiling work on hppa.
Take hppa to PIE as well.
-
Be nice to the sndiod(8) server and align data packets to audio block boundary.
+
Be nice to the sndiod(8) server and align data packets to audio block boundary.
Enable PIE on alpha.
-
Always update ifi->linkstat in dhclient(8) dispatch() loop.
-
Remove support for smtpd(8) encrypted queue, to be reintroduced later.
-
gcc(1) fixed to stop segfaults on landisk when building mysql; PR #28467.
-
Show more precisely what the problem is when using pkg_add(1).
-
Make rc.d(8) "-f" only affect the "start" action.
+
Always update ifi->linkstat in dhclient(8) dispatch() loop.
+
Remove support for smtpd(8) encrypted queue, to be reintroduced later.
+
gcc(1) fixed to stop segfaults on landisk when building mysql; PR #28467.
+
Show more precisely what the problem is when using pkg_add(1).
+
Make rc.d(8) "-f" only affect the "start" action.
-
Compile ld.so(1) with debug info. Helps ld.so(1) hacking and easier to debug code that uses dlopen(3).
-
Allow "filename too long" error message to be seen; error now stops mg(1) exiting when C-x C-c is called.
+
Compile ld.so(1) with debug info. Helps ld.so(1) hacking and easier to debug code that uses dlopen(3).
+
Allow "filename too long" error message to be seen; error now stops mg(1) exiting when C-x C-c is called.
Enable PIE on amd64, mips64(el) and sparc64.
-
Switch gcc(1) to use __guard_local instead of __guard. Allows GCC to emit -fstack-protector code that doesn't need GOT indirection for accessing __guard.
-
Switch gcc(1) to use __guard_local instead of __guard. Allows GCC to emit -fstack-protector code that doesn't need GOT indirection for accessing __guard.
+
Don't enable nginx(8) "sendfile", which does not work on OpenBSD.
-
Make mg(1) more like emacs when opening new buffer: if parent dir is read-only, make buffer read-only; if parent doesn't exist; print message and create buffer as readable.
+
Add support for PIE-by-default in both ld(1) and gcc(1).
+
Don't enable nginx(8) "sendfile", which does not work on OpenBSD.
+
Make mg(1) more like emacs when opening new buffer: if parent dir is read-only, make buffer read-only; if parent doesn't exist; print message and create buffer as readable.
-
Don't force order of cp(1) file and dir creation, was an optimisation with no measurable effect.
-
Instead of tmux(1) requiring a prompt to enter all numbers >10, go back to 0-9a-z, add A-Z and enter the prompt when M-0 to M-9 are pressed (like copy mode).
+
Don't force order of cp(1) file and dir creation, was an optimisation with no measurable effect.
+
Instead of tmux(1) requiring a prompt to enter all numbers >10, go back to 0-9a-z, add A-Z and enter the prompt when M-0 to M-9 are pressed (like copy mode).
-
Fixed dhclient(8) startup causing initial DHCPDISCOVER/DHCPREQUEST packets to be sent multiple times.
-
Bugfix rewrite of the smtpd(8) disk-queue traversal code, and log bogus files found.
+
Use the same compression algorithm, gzip, for smtpd(8) message file and envelopes. Allows inspecting compressed queue with gzcat.
-
Allow compression of messages and envelopes in the queue. To use, add "queue compress" in smtpd.conf(5).
-
smtpd(8) lka must not start servicing requests until it receives full config from parent. Disable imsg from other processes until then. Fixes some races.
-
Pause smtpd(8) accepting clients while below fd reserve limit (or if we fail).
+
Allow compression of messages and envelopes in the queue. To use, add "queue compress" in smtpd.conf(5).
+
smtpd(8) lka must not start servicing requests until it receives full config from parent. Disable imsg from other processes until then. Fixes some races.
+
Pause smtpd(8) accepting clients while below fd reserve limit (or if we fail).
Better detection of the st16650v1 (with broken fifo). Avoids false positives (eg MPC8347 DUART on socppc).
Sparc64 v445 has touchy sleep mode registers, so skip the wakeup code if we are a serial console.
-
Add support for power saving in athn(4) Host AP mode.
-
smtpd(8) live profiling of events: "-T profiling" will log_trace(); "-T profstat" will push info to stats API with type STAT_TIMESPEC under key profiling.imsg.*.
-
Log pause/resume from the administrator to smtpd(8) maillog.
-
Make make(1) wrong variable specs (unterminated) parse errors; add info to be able to pinpoint parse errors at runtime; let job runners abort when a parse error happens while expanding a variable during execution; fix an infinite loop when compiling without FEATURE_RECVARS.
+
Add support for power saving in athn(4) Host AP mode.
+
smtpd(8) live profiling of events: "-T profiling" will log_trace(); "-T profstat" will push info to stats API with type STAT_TIMESPEC under key profiling.imsg.*.
+
Log pause/resume from the administrator to smtpd(8) maillog.
+
Make make(1) wrong variable specs (unterminated) parse errors; add info to be able to pinpoint parse errors at runtime; let job runners abort when a parse error happens while expanding a variable during execution; fix an infinite loop when compiling without FEATURE_RECVARS.
-
Log forced removal and expiration of envelopes to smtpd(8) maillog.
-
When an smtp session fails and IMSG_QUEUE_REMOVE_MESSAGE is sent to the queue, also notify the smtpd(8) scheduler so it can rollback the current update.
-
Added smtpd(8) stat counter for the number of envelopes inflight.
-
In smtpd(8) envelope ascii dump/load: remove loading of evpid; don't dump the msgid; ignore msgid at load.
+
Log forced removal and expiration of envelopes to smtpd(8) maillog.
+
When an smtp session fails and IMSG_QUEUE_REMOVE_MESSAGE is sent to the queue, also notify the smtpd(8) scheduler so it can rollback the current update.
+
Added smtpd(8) stat counter for the number of envelopes inflight.
+
In smtpd(8) envelope ascii dump/load: remove loading of evpid; don't dump the msgid; ignore msgid at load.
Update to unbound 1.4.18 (not yet linked to the build).
-
Added smtpd(8) -N for sendmail compat DSN support; unlimited for now.
-
Fix race in ral(4) rt2661 Tx interrupt processing which can cause Tx processing to get stuck with OACTIVE set, requiring "ifconfig ral0 down up" to un-wedge.
+
Added smtpd(8) -N for sendmail compat DSN support; unlimited for now.
+
Fix race in ral(4) rt2661 Tx interrupt processing which can cause Tx processing to get stuck with OACTIVE set, requiring "ifconfig ral0 down up" to un-wedge.
-
To protect assumptions inside systrace(1), don't let systrace file descriptors be shared between processes.
+
To protect assumptions inside systrace(1), don't let systrace file descriptors be shared between processes.
Build the kernel with -fno-pie.
-
Open a remote file/device with the same dump(8) flags we use when opening a local one.
-
Add ignore keyword to dhclient(8) conf file, allowing one to ignore unwanted info from the server without specifying a supersede value.
-
netstat(1) -h flag added, to print human numbers in conjunction with -w -b
-
Allow smtpd(8) to work as a backup MX, relaying only to MXs with higher priority in the DNS record.
-
smtpd(8) will try to connect to next host if an IO error occurs before the mta is ready to send a mail.
-
Reverse name and meaning of the IFXF_INET6_PRIVACY interface flag (now called IFXF_INET6_NOPRIVACY). IPv6 privacy addresses are on by default without resetting the flag during ifconfig(8) down/up.
-
Fix define of endianness macro used in drm code. Makes radeondrm(4) usable on big-endian archs.
-
Update to nginx(8) 1.2.3, and merge in pcre-8.31.
-
Fix up tmux(1) window reference counting, don't crash if rename timer fires when window is dead but still referenced.
-
Open a remote file/device with the same dump(8) flags we use when opening a local one.
+
Add ignore keyword to dhclient(8) conf file, allowing one to ignore unwanted info from the server without specifying a supersede value.
+
netstat(1) -h flag added, to print human numbers in conjunction with -w -b
+
Allow smtpd(8) to work as a backup MX, relaying only to MXs with higher priority in the DNS record.
+
smtpd(8) will try to connect to next host if an IO error occurs before the mta is ready to send a mail.
+
Reverse name and meaning of the IFXF_INET6_PRIVACY interface flag (now called IFXF_INET6_NOPRIVACY). IPv6 privacy addresses are on by default without resetting the flag during ifconfig(8) down/up.
+
Fix define of endianness macro used in drm code. Makes radeondrm(4) usable on big-endian archs.
+
Update to nginx(8) 1.2.3, and merge in pcre-8.31.
+
Fix up tmux(1) window reference counting, don't crash if rename timer fires when window is dead but still referenced.
+
Added support for .openbsd.randomdata sections and PT_OPENBSD_RANDOMIZE segments to kernel, ld(1), and ld.so(1).
-
Bump smtpd(8) MAX_LINE_SIZE and SMTP_LINE_MAX. Fixes some crashes and "line too long" errors.
-
Stop sending more bytes than necessary with smtpd(8) IMSG_STAT_*.
-
Chroot smtpd(8) scheduler in /var/empty instead of /var/spool/smtpd.
-
Added mfii(4) support for chaining a list off a request frame if it runs out of space for entries.
-
Stop unsetting sysmerge(8) NEED_NEWALIASES too soon, so warnings aren't missed.
+
Added support for .openbsd.randomdata sections and PT_OPENBSD_RANDOMIZE segments to kernel, ld(1), and ld.so(1).
+
Bump smtpd(8) MAX_LINE_SIZE and SMTP_LINE_MAX. Fixes some crashes and "line too long" errors.
+
Stop sending more bytes than necessary with smtpd(8) IMSG_STAT_*.
+
Chroot smtpd(8) scheduler in /var/empty instead of /var/spool/smtpd.
+
Added mfii(4) support for chaining a list off a request frame if it runs out of space for entries.
+
Stop unsetting sysmerge(8) NEED_NEWALIASES too soon, so warnings aren't missed.
-
Skip putting a com(4) port in sleep mode when used as serial console. Allows sparc64 v445 to work flawlessly.
-
Fixed smtpd(8) smtpctl schedule-all and schedule-id .
-
Avoid crash when removing non-existing smtpd(8) envelope.
-
Add warnings on smtpd(8) io errors to help diagnosis.
+
Skip putting a com(4) port in sleep mode when used as serial console. Allows sparc64 v445 to work flawlessly.
+
Fixed smtpd(8) smtpctl schedule-all and schedule-id <msgid>.
+
Avoid crash when removing non-existing smtpd(8) envelope.
+
Add warnings on smtpd(8) io errors to help diagnosis.
-
Introduce smtpd(8) stat_backend, an API for pluggable statistic backends. Statistics: are no longer static structures in shared memory; are only set (smtpd never uses them in its logic); each is a key/value where key can be any (dynamic) string.
+
Introduce smtpd(8) stat_backend, an API for pluggable statistic backends. Statistics: are no longer static structures in shared memory; are only set (smtpd never uses them in its logic); each is a key/value where key can be any (dynamic) string.
Fixed loongson kernel panic when attempting to select glxpcib timecounter as the current timecounter.
-
Disallow empty smtpd(8) domain/address sent after HELO/EHLO command.
-
Limit the number of smtpd(8) bounce sessions running at the same time. Avoids DoS'ing the server when lots of bounces are enqueued at startup.
Improve error reporting in getnameinfo_async() and getaddrinfo_async().
Let xenocara build and release proceed through the exact same steps, avoiding nasty surprises.
-
Fix ftp(1) http resume without out auth (broken on the last commit).
+
Fix ftp(1) http resume without out auth (broken on the last commit).
-
Update dhclient(8) global cur_time after exiting poll() and before calling the state engine, to properly account for time passed.
+
Update dhclient(8) global cur_time after exiting poll() and before calling the state engine, to properly account for time passed.
Update to xf86-video-mach64 6.9.3.
-
Generalise ebus(4/sparc64) code to allow for arbitrary wirings. Makes serial console on the v445 work.
-
Properly initialise the IOMMU control and status register for pyro(4/sparc64). Fixes DMA problems spotted on the v445.
+
Generalise ebus(4/sparc64) code to allow for arbitrary wirings. Makes serial console on the v445 work.
+
Properly initialise the IOMMU control and status register for pyro(4/sparc64). Fixes DMA problems spotted on the v445.
Update to glproto 1.4.16.
-
Fixed typos in DPRINTF() so ehci(4) and uhci(4) error messages refer to correct interface.
+
Fixed typos in DPRINTF() so ehci(4) and uhci(4) error messages refer to correct interface.
Add a default CDIAGFLAGS to bsd.own.mk, so programs may enable warnings by making "make WARNINGS=Yes" without having to add CDIAGFLAGS to its makefile.
Update to pixman 0.26.2.
-
Fix possible ieee80211(9) panic while switching from STA mode into hostap/ibss modes.
-
Fix mips64 and powerpc's ld.so syscall implementations. Prevents gcc(1) from optimising away memory loads and stores that otherwise appear unused in a function.
+
Fix possible ieee80211(9) panic while switching from STA mode into hostap/ibss modes.
+
Fix mips64 and powerpc's ld.so syscall implementations. Prevents gcc(1) from optimising away memory loads and stores that otherwise appear unused in a function.
Update to libGL 7.11.2.
-
Update to myx(4) firmware 1.4.55, via freebsd revision 236212.
-
Added mfi(4) support for "physical devices" on skinny controllers (these let you specify disks that should be accessed directly rather than be part of logical volumes).
+
Update to myx(4) firmware 1.4.55, via freebsd revision 236212.
+
Added mfi(4) support for "physical devices" on skinny controllers (these let you specify disks that should be accessed directly rather than be part of logical volumes).
-
Send ssh(1) client banner immediately, rather than waiting for the server to move first for SSH protocol 2 connections. Based on bz#1999.
-
Print details of which host lines were deleted when using ssh-keygen(1) "-R host".
-
Force a clean shutdown of ssh(1) ControlMaster client sessions when the ~. escape sequence is used. "~." should now work in mux clients even if the server is no longer responding.
+
Send ssh(1) client banner immediately, rather than waiting for the server to move first for SSH protocol 2 connections. Based on bz#1999.
+
Print details of which host lines were deleted when using ssh-keygen(1) "-R host".
+
Force a clean shutdown of ssh(1) ControlMaster client sessions when the ~. escape sequence is used. "~." should now work in mux clients even if the server is no longer responding.
Updates to: xf86-video-cirrus 1.5.1; xf86-video-i740 1.3.4; xf86-video-neomagic 1.2.7; xf86-video-nv 2.1.20; xf86-input-keyboard to 1.6.2; and xf86-input-mouse 1.8.1.
-
Rework mfi(4) so it will do all the completions on a ccb, including calling the done handler. Makes it consistently complete scsi(4) io with all proper error checking.
-
Scrub mfi(4) ccbs when we're about to use them, not when put back on the free list. Old state no longer messes up new commands.
+
Rework mfi(4) so it will do all the completions on a ccb, including calling the done handler. Makes it consistently complete scsi(4) io with all proper error checking.
+
Scrub mfi(4) ccbs when we're about to use them, not when put back on the free list. Old state no longer messes up new commands.
-
Fixed dma sync for the command frame in mfi(4) mfi_done; consolidate other dma syncs.
-
Change gcc(1) to link shared objects with -lpthread and -lc as appropriate (it is no longer necessary to patch software to use -pthread instead of -lpthread).
+
Fixed dma sync for the command frame in mfi(4) mfi_done; consolidate other dma syncs.
+
Change gcc(1) to link shared objects with -lpthread and -lc as appropriate (it is no longer necessary to patch software to use -pthread instead of -lpthread).
On a.out architectures __cerror() is called _cerror(). Fix accordingly so vax can build again.
Enable IPv6 autoconfprivacy by default.
-
Add support for basic ftp(1) HTTP authentication as per RFC 2617 and 3986. Allows "ftp http[s]://user:pass@host/file" idiom.
-
In Xserver(1), allow opening tty[E-J]0. Removed ttyD[1-7], since those devices will never get used by X.
-
Expose the max number of logical volumes mfi(4) supports as the width of its scsibus. Potentially more openings for busy volumes.
-
Boldify tmux(1) windows with alerts in choose-* list.
-
Introduce mfii(4), a driver for the generation of megaraid sas boards.
+
Unset _rcflags and _rcuser so that they don't get inherited by rc.d(8) scripts.
+
Set the rc.d(8) daemon_class as readonly as it should be.
-
Make sure azalia(4) snooping is enabled on Intel 7 Series HD Audio.
+
Make sure azalia(4) snooping is enabled on Intel 7 Series HD Audio.
Fixed bug in m88k siglongjmp(), which would not restore a signal mask of zero.
-
Mask the bgpd(8) reserved bits and the ext len bit in the attribute flags field. Fixes session failures and ensures updates sent out are correct when the wrong data is received from other systems.
-
Fixed Xserver(1) privilege separation regression, where parent pid was initialised too late.
-
mandoc(1) .Sq will now use curly right quotes in HTML output to match its curly left quotes; properly reinitialise the styles attribute string buffer for each column, so attributes don't accumulate.
+
Mask the bgpd(8) reserved bits and the ext len bit in the attribute flags field. Fixes session failures and ensures updates sent out are correct when the wrong data is received from other systems.
+
Fixed Xserver(1) privilege separation regression, where parent pid was initialised too late.
+
mandoc(1) .Sq will now use curly right quotes in HTML output to match its curly left quotes; properly reinitialise the styles attribute string buffer for each column, so attributes don't accumulate.
-
ld(1) will now correctly handle -rpath-link, instead of eating its argument and handling it as -r.
-
Fix ahci(4) state tracking for the error ccb, to stop "ccb->ccb_xa.state == ATA_S_ONCHIP" assertion failures when talking to dying disks.
-
Instead of numbering tmux(1) "choose mode" items 0-9a-z and then nothing, number them all and if there are more than 10 use a prompt when 0-9 is pressed.
+
Instead of numbering tmux(1) "choose mode" items 0-9a-z and then nothing, number them all and if there are more than 10 use a prompt when 0-9 is pressed.
-
Producer/consumer values used by the mfi(4) device should be little endian. Byteswap where appropriate.
+
Producer/consumer values used by the mfi(4) device should be little endian. Byteswap where appropriate.
-
oce(4) improvements: properly account for cluster chains the driver builds upon receiving a jumbo frame; set a timeout in case the oce(4) chip goes out to lunch; respect the mtu value that ifconfig sets; schedule a rx refill if the ring is empty; try to make sense of the firmware statistics by counting rx and tx errors; and no longer compile rss functions in unless OCE_RSS is specified.
-
Allow smtpd(8) failure reports for different recipients of the same message to be grouped into a single bounce message.
-
Improve the smtpd(8) message flows to isolate operations on the queue backend within the queue process.
+
oce(4) improvements: properly account for cluster chains the driver builds upon receiving a jumbo frame; set a timeout in case the oce(4) chip goes out to lunch; respect the mtu value that ifconfig sets; schedule a rx refill if the ring is empty; try to make sense of the firmware statistics by counting rx and tx errors; and no longer compile rss functions in unless OCE_RSS is specified.
+
Allow smtpd(8) failure reports for different recipients of the same message to be grouped into a single bounce message.
+
Make all ehci(4), ohci(4) and uhci(4) *_device_*_start() functions wait for an interrupt when the bus is in polling mode. Stops some ending at ddb> after running "halt -p".
-
Native build system for gl-docs. Removes last dependency in xenocara on imake(1).
-
Fixed bug in smtpd(8) evpid parsing on 32bit archs.
-
In Xserver(1)'s non-privilege separation mode, avoid accidentally sending a SIGUSR1 signal to init(8).
-
Store the data used to generate an icmp(4) error message on a stack instead of allocating a new mbuf.
-
Multibyte input to cwm(1) menu code now possible.
+
Make all ehci(4), ohci(4) and uhci(4) *_device_*_start() functions wait for an interrupt when the bus is in polling mode. Stops some ending at ddb> after running "halt -p".
+
Native build system for gl-docs. Removes last dependency in xenocara on imake(1).
+
Fixed bug in smtpd(8) evpid parsing on 32bit archs.
+
In Xserver(1)'s non-privilege separation mode, avoid accidentally sending a SIGUSR1 signal to init(8).
+
Store the data used to generate an icmp(4) error message on a stack instead of allocating a new mbuf.
+
Multibyte input to cwm(1) menu code now possible.
-
Added support for ix(4) 10Gb ethernet cards based on the Intel X540 chipset.
+
Added support for ix(4) 10Gb ethernet cards based on the Intel X540 chipset.
Update to xserver 1.12.3.
-
If dbus is installed, xdm(1) and xinit(1) will now start the daemon as part of the X session.
+
If dbus is installed, xdm(1) and xinit(1) will now start the daemon as part of the X session.
Switched to automake 1.12/autoconf 2.69.
-
Add a new rc.d(8) rc_usercheck variable (default to YES). When set to no, root privilege is needed to run rc_check. This means /etc/rc.d/foobar check can now be run as a regular user.
-
sysmerge(8) now also logs the file(s) we manually merged/installed.
+
Add a new rc.d(8) rc_usercheck variable (default to YES). When set to no, root privilege is needed to run rc_check. This means /etc/rc.d/foobar check can now be run as a regular user.
+
sysmerge(8) now also logs the file(s) we manually merged/installed.
-
Added driver for oce(4) Emulex OneConnect 10Gb Ethernet, for cards based on ServerEngines BladeEngine 2 and 3, and Emulex Lancer (XE201).
+
Added driver for oce(4) Emulex OneConnect 10Gb Ethernet, for cards based on ServerEngines BladeEngine 2 and 3, and Emulex Lancer (XE201).
-
Reset the smtpd(8) session if no RCPT was accepted for the batch.
-
Fixed bogus smtpd(8) permfail when no MX is defined on a valid domain.
-
In smtpd(8) format string expansion, lowercase() all. Fixes issue where a %u format could lead to a delivery failure (ie: GILLES@openbsd.org should be expanded to gilles (not GILLES) for local deliveries).
-
Disable mandoc(1) hyphenation and, for nroff, disable justification. Consistent with how mdoc behaves (and produces more readable manuals).
-
Quote the '-' before the mandoc(1) flags, to prevent nroff from putting a line break between the '-' and the flag character.
-
Use "\\ " not "\\~" in mandoc(1) as the non-breaking space (historic nroff doesn't support the latter).
-
Implement .PD for mandoc(1) -Tascii. Reduces mandoc/groff differences in base by 25%.
+
Reset the smtpd(8) session if no RCPT was accepted for the batch.
+
Fixed bogus smtpd(8) permfail when no MX is defined on a valid domain.
+
In smtpd(8) format string expansion, lowercase() all. Fixes issue where a %u format could lead to a delivery failure (ie: GILLES@openbsd.org should be expanded to gilles (not GILLES) for local deliveries).
+
Disable mandoc(1) hyphenation and, for nroff, disable justification. Consistent with how mdoc behaves (and produces more readable manuals).
+
Quote the '-' before the mandoc(1) flags, to prevent nroff from putting a line break between the '-' and the flag character.
+
Use "\\ " not "\\~" in mandoc(1) as the non-breaking space (historic nroff doesn't support the latter).
+
Implement .PD for mandoc(1) -Tascii. Reduces mandoc/groff differences in base by 25%.
-
Fix initialisation of audioctl(1) "oldval" field, bug introduced in r1.20.
+
Fix initialisation of audioctl(1) "oldval" field, bug introduced in r1.20.
-
Load os passive fingerprints when testing the pfctl(8) ruleset.
+
Load os passive fingerprints when testing the pfctl(8) ruleset.